Whirlpool Cabrio W10151492A Instrukcja obsługi i konserwacji - Strona 14

Przeglądaj online lub pobierz pdf Instrukcja obsługi i konserwacji dla Suszarka Whirlpool Cabrio W10151492A. Whirlpool Cabrio W10151492A 48 stron. Fabric care system electric dryer

Drukuj stronę

1. Tools and Parts

Vent system chart

NOTE: Performance of rear exhaust to either side of the dryer is

equivalent to adding one elbow. To determine maximum exhaust

length, add one elbow to the chart.

Number of

Type of

90º turns

vent

or elbows

Rigid metal

Flexible metal

Rigid metal

Flexible metal

Rigid metal

Flexible metal

Rigid metal

Flexible metal

Rigid metal

Flexible metal

Install Vent System

1. Install exhaust hood. Use caulking compound to seal exterior

wall opening around exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust

hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

3. Run vent to dryer location. Use the straightest path possible.

See "Determine vent path" in "Plan Vent System." Avoid 90º

turns. Use clamps to seal all joints. Do not use duct tape,

screws or other fastening devices that extend into the interior

of the vent to secure vent.

Install Leveling Legs

WARNING

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

1. To protect the floor, use a large, flat piece of cardboard from

the dryer carton. Place cardboard under the entire back edge

of the dryer.

2. Firmly grasp the body of the dryer (not the top or console

panel). Gently lay the dryer on the cardboard. See illustration.

Box or

Angled

Louvered

hoods

64 ft (20 m)

58 ft (17.7 m)

36 ft (11 m)

28 ft (8.5 m)

54 ft (16.5 m)

48 ft (14.6 m)

31 ft (9.4 m)

23 ft (7 m)

44 ft (13.4 m)

38 ft (11.6 m)

27 ft (8.2 m)

19 ft (5.8 m)

35 ft (10.7 m)

29 ft (8.8 m)

25 ft (7.6 m)

17 ft (5.2 m)

27 ft (8.2 m)

21 ft (6.4 m)

23 ft (7 m)

15 ft (4.6 m)

3. Examine the leveling legs. Find the diamond marking.

4. Screw the legs into the leg holes by hand. Use a wrench to

finish turning the legs until the diamond marking is no longer

visible.

5. Place a carton corner post from dryer packaging under each

of the 2 dryer back corners. Stand the dryer up. Slide the

dryer on the corner posts until it is close to its final location.

Leave enough room to connect the exhaust vent.

Connect Vent

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in

dryer. If connecting to existing vent, make sure the vent is

clean. The dryer vent must fit over the dryer exhaust outlet

and inside the exhaust hood. Check that the vent is secured

to exhaust hood with a 4" (10.2 cm) clamp.

2. Move dryer into its final location. Do not crush or kink vent.

3. (On gas models) Check that there are no kinks in the flexible

gas line.

4. Once the exhaust vent connection is made, remove the

corner posts and cardboard.

Level Dryer

Check the levelness of the dryer by first placing a level on the top

of the dryer near the console.

Then, by placing a level in the crease on the side of the dryer

between the top of the dryer and the dryer cabinet, check the

levelness from front to back.

If the dryer is not level, prop up the dryer using a wood block.

Use a wrench to adjust the legs up or down and check again for

levelness.