Whirlpool Duet GGW9250SU0 Instrukcja obsługi i konserwacji - Strona 6
Przeglądaj online lub pobierz pdf Instrukcja obsługi i konserwacji dla Suszarka Whirlpool Duet GGW9250SU0. Whirlpool Duet GGW9250SU0 48 stron. Electronic gas dryer
Drukuj stronęDoor Reversal Kit
Are you planning to reverse the door swing direction on your
DUET®dryer? To do so, you will need to purchase a Door
Reversal Kit.
To order, call the dealer from whom you purchased your dryer or
refer to the "Assistance
or Service" section of this manual. Ask
for Part Number 8530069 (Shield Blue), 8530070 (Shield
Platinum), 8530071 (Biscuit), 8530072 (Pewter) or 8579123
(Diamond Dust [Silver]).
Door Reversal and Stack Combination
Kit
Are you planning to reverse the door swing direction on your
DUET®dryer and stack your DUET®washer and dryer? To do so,
you can purchase a Door Reversal and Stack Combination
Kit.
To order, call the dealer from whom you purchased your dryer or
refer to the "Assistance
or Service" section of this manual. Ask
for Part Number 8530073 (Shield Blue), 8530074 (Shield
Platinum), 8530075 (Biscuit), 8530076 (Pewter) or W10057200
(Diamond Dust [Silver]).
Backguard
If you are installing your DUET ° washer and dryer and wish to
avoid having loose items fall behind your machines, you may
purchase a pair of washer/dryer
backguards.
These will reduce
the chance of items falling behind the machines during operation.
To order, call the dealer from whom you purchased your dryer or
refer to the "Assistance
or Service" section of this manual. Ask
for Part Number 8558694 (White), 8558695 (Biscuit), 8558696
(Pewter), or W10057220 (Diamond Dust [Silver]).
A level floor with a maximum slope of 1" (2.5 cm) under entire
dryer. If slope is greater than 1" (2.5 cm), install Extended
Dryer Feet Kit, Part Number 279810. Clothes may not tumble
properly, and automatic sensor cycles may not operate
correctly if dryer is not level.
For a garage installation, you will need to place the dryer at
least 18" (46 cm) above the floor. If you are using a 10"
(25.4 cm) pedestal, you will need to place the pedestal at
least 9" (22.9 cm) above the floor. With a 13" (33 cm)
pedestal, you will need to place the pedestal at least
6" (15.2 cm) above the floor. With a 15.5" (39.4 cm) pedestal,
you will need to place the pedestal at least 3.5" (8.9 cm)
above the floor.
Do not operate your dryer at temperatures
below 45°F (7°C). At
lower temperatures,
the dryer might not shut off at the end of an
automatic cycle. This can result in longer drying times.
The dryer must not be installed or stored in an area where it will
be exposed to water and/or weather.
Check code requirements. Some codes limit, or do not permit,
installation of the dryer in garages, closets, mobile homes or
sleeping quarters. Contact your local building inspector.
NOTE: No other fuel-burning
appliance can be installed in the
same closet as a dryer.
Installation
clearances
The location must be large enough to allow the dryer door to
open fully.
Dryer Dimensions
Explosion
Hazard
Keep flammable
materials
and vapors, such as
gasoline,
away from dryer.
Place dryer at _east 18 inches (48 cm) above the floor
for a garage installation.
Failure to do so can result
in death, explosion,
or fire.
You will need
•
A location that allows for proper exhaust installation. A gas
dryer must be exhausted to the outdoors. See "Venting
Requirements."
A grounded electrical outlet located within 2 ft (61 cm) of
either side of the dryer. See "Electrical Requirements."
A sturdy floor to support the total dryer weight of 200 Ibs
(90.7 kg). The combined weight of a companion
appliance
should also be considered.
i
(80 cm) ,
"-
27"
*Most installations require a minimum 5" (12.7 cm) clearance
behind the dryer for the exhaust vent with elbow. See "Venting
Requirements."
Installation
spacing for recessed
area or closet installation
The following spacing dimensions are recommended
for this
dryer. This dryer has been tested for spacing of 0" (0 cm)
clearance on the sides and rear. Recommended
spacing should
be considered for the following reasons:
•
Additional spacing should be considered for ease of
installation and servicing.
•
Additional clearances might be required for wall, door and
floor moldings.
•
Additional spacing should be considered on all sides of the
dryer to reduce noise transfer.
For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
•
Companion appliance spacing should also be considered.