Whirlpool WGD9400SZ3 Instrukcja obsługi i konserwacji - Strona 12
Przeglądaj online lub pobierz pdf Instrukcja obsługi i konserwacji dla Suszarka Whirlpool WGD9400SZ3. Whirlpool WGD9400SZ3 29 stron. Duet / duet steam electronic dryer
Drukuj stronę
Confirm your vent system falls within the recommended
run length and number of elbows for the type of vent you
are using. Refer to "Plan Vent System" in the Installation
Instructions for details.
•
Select a Timed Dry heated cycle, and restart the dryer.
If the message persists, have your entire home venting run
cleaned.
"E" Variable (El, E2, E3) service codes:
Call for service.
Clothes are not drying satisfactorily, drying times are too long,
or load is too hot
Is the lint screen clogged with lint?
Lint screen should be cleaned before each load.
Has the Air Only temperature setting been selected?
Select the right temperature for the types of garments being
dried. See "Additional Features."
Is the load too large and heavy to dry quickly?
Separate the load to tumble freely.
Are clothes coming out of the Refresh cycle with damp or
wet spots?
Under certain environmental or installation conditions you may
experience underdrying.
Select the Touch Up cycle (20 min.
default time), which can be customized
by selecting High
temperature and/or additional cycle time by pressing the Dry
Time up button.
Is the exhaust vent or outside exhaust hood clogged with
lint, restricting air movement?
Run the dryer for 5-10 minutes. Hold your hand under the
outside exhaust hood to check air movement.
If you do not
feel air movement, clean exhaust system of lint or replace
exhaust vent with heavy metal or flexible metal vent. See the
Installation Instructions.
Are fabric softener sheets blocking the grille?
Use only one fabric softener sheet, and use it only once.
Is the exhaust vent the correct length?
Check that the exhaust vent is not too long or has too many
turns. Long venting will increase drying times. See the
Installation Instructions.
Is the exhaust vent diameter the correct size?
Use 4" (102 mm) diameter vent material.
Is the dryer located in a room with temperature
below 45°F
(7°C)?
Proper operation of dryer cycles requires temperatures above
45°F (7°C).
Is the dryer located in a closet?
Closet doors must have ventilation openings at the top and
bottom of the door. The front of the dryer requires a minimum
of 1" (25 mm) of airspace, and, for most installations, the rear
of the dryer requires 5" (127 mm). See the Installation
Instructions.
Cycle time too short
Is the automatic cycle ending early?
The load may not be contacting the sensor strips. Level the
dryer.
Change the dryness level setting on Automatic
Cycles.
Increasing or decreasing the dryness level will change the
amount of drying time in a cycle.
Lint on load
•
Is the lint screen clogged?
Clean lint screen. Check for air movement.
Stains on load or drum
Was dryer fabric softener properly used?
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially dried load can
stain your garments. Do not use fabric softener sheets with
steam cycles.
Drum stains are caused by dyes in clothing (usually blue
jeans). These will not transfer to other clothing.
Loads are wrinkled
Was the load removed from dryer at the end of the cycle?
Select Enhanced Touch Up Cycle to tumble the load with
water and heat. This cycle is best for smoothing out wrinkles
and reducing odors from loads consisting of wrinkle-free
cotton, cotton polyester blends, common knits and synthetic
garments.
NOTE: Refer to garment care label instructions. Dry clean only
garments are not recommended.
Loads are still wrinkled following Steam Cycle?
Make sure water is connected to the dryer. Check that water
inlet hose is connected to both the faucet and dryer's water
inlet valve. Check that the water supply is turned on.
Was the dryer overloaded?
Dry smaller loads that can tumble freely. Smaller loads of 1-4
garments yield best results with Quick Refresh Cycle. Results
may also vary depending on fabric type. This cycle is best for
reducing wrinkles and odors from loads consisting of wrinkle-
free cotton, cotton polyester blends, common knits and
synthetics.
Odors
Have you recently been painting, staining, or varnishing in
the area where your dryer is located?
If so, ventilate the area. When the odors or fumes are gone
from the area, rewash and dry the clothing.
Is water connected to the dryer?
Check that water inlet hose is connected to both the faucet
and dryer's water inlet valve. Check that the water supply is
turned on.
To remove odors left in garments after wearing, select Quick
Refresh for small loads of 1-4 garments. This cycle is best for
reducing wrinkles and odors from loads consisting of wrinkle-
free cotton, cotton polyester blends, common knits, and
synthetics.
12