Whirlpool YCEE2760KQ0 Instrukcja instalacji - Strona 7
Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Suszarka Whirlpool YCEE2760KQ0. Whirlpool YCEE2760KQ0 27 stron. Commercial dryer gas or electric
Drukuj stronę
Electrical
requirements
If codes permit and a separate
ground wire is used, it is
recommended
that a qualified
electrician
determine
that the ground
path is adequate.
Important: Observe all governing
codes
and ordinances.
A four-wire
or three-wire
(Canada:
four-wire
only), single-phase,
120/240-
volt, 60-Hz, AC-only
electrical
supply
(or four-wire
or three-wire,
120/208-
volt, if specified
on the model/serial
rating plate)
is required
on a
separate,
30-ampere
circuit, fused on
both sides of the line, A time-delay
fuse or circuit
breaker
is
recommended,
Recommended
ground method
In U.S.:
It is the personal
responsibility
and
obligation
of the customer
to contact
a qualified
electrician
to assure that
the electrical
installation
is adequate
and in conformance
with the
National
Electrical
Code,
ANSI/NFPA
70*, and all local codes and
ordinances,
In Canada.:
It isthe personal
responsibility
and
obligation
of the customer
to
install the dryer in accordance
with CAN 1-B149 installation
codes'*
and all national
or local
codes.
Canadian
models are equipped
with a four-wire,
30-amp
rated
flexible-type
power
cord. The
power
cord must be plugged
into
a mating
30-amp
receptacle.
(NEMA type 14-30R).
Copies
of the standards
listed above
may
be obtained
from:
* National
Fire Protection
Association
One Baited/march
Park
Quincy,
Massachusetts
02269
**CSA International
8501 East Pleasant
Valley Road
Cleveland,
Ohio 44131 _75
Now Start...
Excessive Weight Hazard
Usetwo or more peopleto moveand
installdryer.
Failureto do so can resultin backor
other injury.
With dryer in laundry area...
exhaust
fuse
syste_vent
disconnect
l
mTake tape
off front corners of
dryer, Open dryer and remove the
literature
and parts packages,
Wipe
the interior of the drum thoroughly
with a damp
cloth,
mTake two of the cardboard
corners from the carton
and place
them on the floor in back of the dryer,
Firmly grasp the body of the dryer
and gently
lay it on its back on the
cardboard
corners,
mWith one of the legs in hand,
check
the ridges for a diamond
marking, That's how far the leg is
supposed
to go into the hole,
mStaff to screw the leveling
legs
into the holes by hand,
(Use a small
amount
of liquid detergent
to
lubricate
the screw threads
so it is
easier to turn the legs,) Use a 1-inch
wrench
or socket wrench
to finish
turning
the legs until you reach the
diamond
mark,
Now stand the dryer up,
Slide dryer onto cardboard
or
hardboard
before moving across floor
to avoid damaging
floor covering.
mRemove
the service door of the
meter case, Lift
the service door
up at the back
and remove,
Install money-
accepting
device,
(Refer to
manufaturer's
instructions
for proper
installation,)
For dryers using coin slides, use
adapter
kit supplied
with dryer,
Replace
the meter case service door,
Put the coin vault with lock and key
the meter case opening,
m Move dryer close to final
position,
Remove
cardboard
or
hardboard
from under dryer,
Page 7