Whirlpool YCEM2760TQ0 Instrukcja instalacji - Strona 11

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Suszarka Whirlpool YCEM2760TQ0. Whirlpool YCEM2760TQ0 36 stron. Commercial gas or electric dryer

Drukuj stronę

(not the air cycle), let the dryer run for at least five minutes.

Dryer will stop when time is used up.

NOTE: Dryer door must be closed for dryer to operate. When

door is open, dryer stops, but timer continues to run. To

restart dryer, close door and push START/RESTART button.

4. If the burner does not ignite and you can feel no heat inside

the dryer, shut off dryer for five minutes. Check that all supply

valve controls are in "ON" position and that the electrical cord

is plugged in. Repeat five-minute test.

5. If drying time is too long, make sure lint screen is clean.

INSTALLATION INSTRUCTIONS - ELECTRICDRYER

The console houses the factory-installed

accumulator timer with

actuating arm and button.

The factory-installed

timer is set to provide 45 minutes (4 pins) of

drying time when activated by the coin s!ide. Timer cams for

30-minute (6 pins) and 60-minute (3 pins) drying times are

included in the parts bag.

The coin slide mechanism, control panel lock and key, and coin

box lock and key are not included and are available from usual

industry sources.

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

NOTE: Slide dryer onto cardboard or hardboard before moving to

avoid damaging floor covering.

1. Using two or more people, move dryer to desired installation

location.

2. Take tape off front corners of dryer. Open dryer and remove

the literature and parts packages. Wipe the interior of the

drum thoroughly with a damp cloth.

3. Take two of the cardboard corners from the carton and place

them on the floor in back of the dryer. Firmly grasp the body

of the dryer and gently lay it on its back on the cardboard

corners.

4. With one of the legs in hand, check the ridges for a diamond

marking. That's how far the leg is supposed to go into the

hole.

5. Start to screw the leveling legs into the holes by hand. (Use a

small amount of liquid detergent to lubricate the screw

threads so it is easier to turn the legs.) Use a 1-inch wrench or

socket wrench to finish turning the legs until you reach the

diamond mark.

Now stand the dryer up.

6. Remove the service door of the meter case by lifting it up at

the back. Install the money-accepting

device. (Refer to

manufacturer's

instructions for proper installation.)

Replace the meter case service door. Put the coin vault with

lock and key in the meter case opening.

8. Remove cardboard or hardboard from under dryer.

Power

Supply

Cord

Method

= U.S. Onty

This dryer is manufactured with the neutral ground wire

connected to the neutral (center) of the wiring harness at the

terminal block. If local codes do not permit this type of

connection, use "Four-wire connection"

instructions.

Use a UL-tisted power supply cord rated 240-volt min.,

30-amp and marked for use with a clothes dryer.

Fire Hazard

Use a new UL listed 30 amp power suppmy cord,

Use a UL listed strain

remief.

Disconnect

power before making electrical

connections.

Connect

neutral wire (white or center wire) to center

terminam (silver).

Ground wire (green or bare wire) must be connected

green ground

connector.

Connect

remaining

2 supply wires to remaining

2 terminams (gold).

Securely

tighten

aH electricam connections,

Failure to do so can result in death, fire, or

electricam shock.

1. Disconnect power.

For dryers using coin slides, use the adapter kit supplied with

the dryer.