Whirlpool YWED7500VW Instrukcja obsługi i konserwacji - Strona 6
Przeglądaj online lub pobierz pdf Instrukcja obsługi i konserwacji dla Suszarka Whirlpool YWED7500VW. Whirlpool YWED7500VW 36 stron.
Drukuj stronę
Installation Clearances
The location must be large enough to allow the dryer door
to open fully.
Dryer Dimensions
39"
(991 mm)
23
3
⁄
"
8
(593.7 mm)
3
⁄
"
1
16
(77.5 mm)
BACK VIEW
26"
(660 mm)
approx.
1
⁄
"
2
(12.5 mm)
Exhaust 4"
(102 mm) dia.
*Most installations require a minimum 5½" (140 mm) clearance
behind the dryer for the exhaust vent with elbows. See "Venting
Requirements."
Installation spacing for recessed area and closet installations
The following spacing dimensions shown are recommended
when the dryer is to be operated with, or without, the Stack Kit.
This dryer has been tested for installation with spacing of
0" (0 mm) clearance; however, spacing of 1" (25 mm) clearance is
recommended. Recommended spacing should be considered for
the following reasons:
Additional spacing should be considered for ease of
installation and servicing.
Additional spacing should be considered on all sides of the
dryer to reduce noise transfer.
For closet installation with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation opening are
acceptable.
Companion appliance spacing should also be considered.
To purchase a Stack Kit, see "Assistance or Service."
Custom undercounter installation - Dryer only
0"
(0 mm)
33
1
⁄
" min.
4
(844.5 mm)
0"
6
(0 mm)
*
23¼"
(603 mm)
33¼"
(844.5 mm)
11
5
⁄
"
8
(295 mm)
32
3
⁄
"
4
(832 mm)
2
⁄
"
1
8
(54 mm)
0"
23
3
⁄
"
8
(593.7 mm)
(0 mm)
Recessed or closet installation - Dryer only
14"
(356 mm)
18" (457 mm)
3"
(76 mm)
0"
1" (25 mm)
(0 mm)
A
A. Side view - closet or confined area
B. Recessed area
C. Closet door with vents
Recessed or closet installation - Stacked with stack kit
(Accessory)
12"
(305 mm)
DRYER
WASHER
0" (0 mm)
0" (0 mm)
1" (25 mm)
A
A. Recessed area
B. Side view - closet or confined area
C. Closet door with vents
3
⁄
1
16
(77.5 mm)
BACK VIEW
59"
(1500 mm)
approx.
1
⁄
"
2
(12.5 mm)
Mobile Home - Additional Location Requirements
This dryer is suitable for mobile home installations.
The installation must conform to the Manufactured Home
Construction and Safety Standard CAN/CSA-Z240 MH.
Mobile home installations require:
Metal exhaust system hardware, which is available for
purchase from your dealer.
Special provisions must be made in mobile homes to
introduce outside air into the dryer. The opening (such as a
nearby window) should be at least twice as large as the dryer
exhaust opening.
48 in.
2
(310 cm
2
)
24 in.
2
(155 cm
2
)
0"
(0 mm)
B
C
3" (76 mm)
48 in.
2
(310 cm
2
)
24 in.
2
(155 cm
2
)
B
C
"
11
⁄
"
5
8
(295 mm)
Exhaust
65
3
⁄
"
4
(1670 mm)
35
⁄
"
1
8
(892 mm)
3"
(76 mm)
3"
(76 mm)
3"
(76 mm)
3"
(76 mm)