Whirlpool 30 " Eye-Level Gas Range Instrukcja instalacji - Strona 14

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Okap wentylacyjny Whirlpool 30 " Eye-Level Gas Range. Whirlpool 30 " Eye-Level Gas Range 32 stron. Freestanding gas range with self-cleaning oven
Również dla Whirlpool 30 " Eye-Level Gas Range: Instrukcje instalacji oraz instrukcja obsługi i konserwacji (32 strony), Instrukcja instalacji (11 strony), Instrukcje instalacji oraz instrukcja obsługi i konserwacji (28 strony), Instrukcja instalacji (11 strony), Instrukcje instalacji (5 strony), Instrukcja instalacji (28 strony), Instrukcja instalacji (48 strony), Instrukcja instalacji (12 strony), Instrukcje instalacji (5 strony), Instrukcja instalacji (7 strony), Instrukcja instalacji (7 strony), Instrukcja instalacji (7 strony), Instrukcje instalacji (5 strony), Instrukcja instalacji (7 strony), Instrukcja instalacji (10 strony)

Drukuj stronę

Install Warming Drawer Deflector Kit (only

for ovens installed above warming

drawers)

On single and double oven models installed above a warming

drawer, a warming drawer deflector kit must be installed. See the

"Tools and Parts" section for information on ordering.

NOTE: Warming drawer deflector is not needed if feet are

installed in the tall position and bottom vent trim has been

installed.

Parts Supplied in Deflector Kit

A. Phillips head screws (4)

only 2 screws for 27" (68.6 cm) size

B. Warming drawer deflector (1)

Install Deflector Kit

1. Flex the upper vent piece (C) away from the lower vent piece

(D) to slide the warming drawer deflector (B) between them.

Some force may be required to flex the upper vent trim (C)

away from the lower vent trim (D). Some force may also be

required to flex the warming drawer deflector (B) and slide it

into position. Make sure screw holes are properly aligned

between the two pieces. See the following illustration.

2. Install the warming drawer deflector (B) to the lower vent

piece (D) using two #8-18 x

NOTE: On 27" (68.6 cm) models, only one #8-18 x ¼" screw

is used on each side.

¹⁄₄

A. #8-18 x

" screws

B. Warming drawer deflector

3. Align vent tab (B) with oven frame (A) as shown in the

following illustration.

¹⁄₄

" screws on each side.

C. Upper vent piece

D. Lower vent piece

4. Using one #8-18 x ³⁄₈" screw (E) on each side of the vent tab

(B), fasten the vent securely to the oven.

A. Oven frame

B. Vent tab

C. Oven vent

Complete Installation

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. For oven use and cleaning, read the Use and Care Guide.

Check Operation of Single and Double Ovens

1. Turn power on.

2. At first use, set up the clock and any other preferences if

available. For more information, read the Use and Care

Guide.

3. Press BROIL on single oven models.

NOTE: Press UPPER BROIL or LOWER BROIL on double

oven models.

4. Set the temperature.

5. Press START.

If oven(s) does not operate, check the following:

Household fuse is intact and tight; or circuit breaker has

not tripped.

Electrical supply is connected.

See "Troubleshooting" section in the Use and Care Guide.

6. When oven has been on for 5 minutes, feel for heat.

If you do not feel heat or if an error message appears in the

display, turn off the oven and contact a qualified technician.

7. Press UPPER CANCEL/LOWER CANCEL on double ovens,

or press CANCEL on single ovens.

If you need Assistance or Service:

Please reference the "Assistance or Service" section of the Use

and Care Guide or contact the dealer from whom you purchased

your built-in oven.

D. Warming drawer deflector

³⁄₈

E. #8-18 x

" screw