Electrical
connection
Electrical Shock Hazard
l
Electrical ground is required on this
appliance.
l
Do Not connect to the electrical
supply until appliance
is
permanently
grounded.
l
Disconnect power to the junction
box before making the electrical
connection.
l
This appliance
must be connected
to a grounded,
metallic, permanent
wiring system, or a grounding
connector
should be connected
to
the grounding terminal or wire lead
on the appliance.
Failure to do so could result in a fire,
personal injury or electrical shock.
This appliance
is manufactured
with
white (neutral) power supply wire and a
cabinet-connected
green grounding
wire twisted together.
Connect the appliance
cable to the
junction box through the U.L.-listed
conduit connector.
Complete electrical
connection
according
to local codes
and ordinances.
A. Where local codes permit.
connecting
the cabinet-grounding
conductor
to the neutral (white) junction
box wire:
Cable
from
Junction
power
supply
LJ.L.-listed
conduit
Figure 1
CableTom
connector
range
Grounded Neutral
1. Disconnect the power supply.
2. Connect together 3 wires: green and
white appliance
cable wires and the
neutral (white) wire in junction box.
3. Connect the two black wires together;
then the two red wires together. See
Figure 1.
B. Where local codes Do
Not permit...
connecting
the cabinet-grounding
conductor
to the neutral (white) junction
box wire:
Junction
Cable
from
bzsyr
supply
wiresw
White
wires
Bare
green
L
ack
ires
Wires
Cable from
conduit
range
connector
Figure 2
Ungrounded
Neutral
1. Disconnect the power supply.
P.Separate the green and white
appliance
cable wires.
3. Connect the white appliance
cable
wire to the neutral (white) wire in the
junction box.
4. Connect the two black wires; then the
two red wires. See Figure 2.
5. Connect the green grounding wire to a
grounded wire in the junction box.
Panel B
. .
C. If connecting
to a four-
wire electrical system:
DO NOT connect the cabinet-grounding
conductor
to the neutral (white) junction
box wire.
Junction
Cable
frl om
box pi
suPPlY
White
Fig! ure 3
range
connector
1. Disconnect the power supply.
2. Separate the green and white
appliance
cable wires.
3. Connect the white appliance
cable
wire to the neutral (white) wire in the
junction box.
4. Connect the two black wires; then the
two red wires. See Figure 3.
5. Connect the green grounding wire to
the grounding wire in the junction box.
Now start...
with oven in kitchen.
1
1 w Remove shipping materials, tape,
and protective
film from range. Do Not
remove shipping base at this time.
2
w Remove the racks and other parts
from inside the oven.
3
w Insert a nail or a 5/32' diameter
item in the hole in each of the hinges.
Close the door as far as possible. Lift oven
door off of the hinges and set aside.
Floor Damage
Before moving range across floor,
check that range is on shipping base
or slide range onto cardboard
or
hardboard.
Failure to do so could cause damage
to floor covering.
4
n
Move range close to cabinet
cutout. Make electrical connection.
See
Electrical requirements and Electrical
connection
sections, Panels A and B, for
details.
Personal Injury Hazard
Because of the weight and size this
range, two or more people are
needed to move and safely install it.
Failure to do so could result in
personal injury.
Remove and discard shipping
base. Lift range up into cabinet opening
using the oven opening as an area to
grip.
6
w Center range in cabinet cutout.
Loosen screws and insert spacers
(shipped in literature bag) on each side
of the control console. If range does not
fit properly, check spacers. The spacers
may need to be cut to fit under the
countertop.
Mark with a pencil where
each spacer needs to be cut. Loosen
both screws to remove spacers, Cut
across top of each spacer. Replace
spacers and tighten screws. Check that
range fits properly on countertop.
Drukuj stronę