Whirlpool 36'' Freestanding Gas Range Instrukcja instalacji - Strona 4

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Okap wentylacyjny Whirlpool 36'' Freestanding Gas Range. Whirlpool 36'' Freestanding Gas Range 7 stron. 30" and 36" gas sealed burner cooktop
Również dla Whirlpool 36'' Freestanding Gas Range: Instrukcja instalacji (13 strony), Instrukcja instalacji (10 strony), Instrukcja instalacji (7 strony), Instrukcje instalacji oraz instrukcja obsługi i konserwacji (28 strony), Instrukcja instalacji (28 strony), Instrukcja instalacji (6 strony), Instrukcja instalacji (7 strony), Instrukcje instalacji (5 strony)

Whirlpool 36'' Freestanding Gas Range Instrukcja instalacji
Install anti-tip bracket on floor:
*Measure and mark a line at the center
of the cabinet opening on the rear
wall. Measure and mark lines 15 13/ 16"
and 16- 15/ 16" from either the left
(shown) or right side of the centerline
on the rear wall. Measure and mark on
the rear wall a line 1" from the floor.
Note: If there is a cabinet on only one
side, install the anti-tip bracket next to
the cabinet, using the measurements
given.
range into final
position. Remove
the broiler drawer.
LOOK
under range (a flashlight may be
needed) to check that anti-tip bracket
overlaps range base. If anti-tip bracket
does not overlap base, remove range
and reposition bracket to insure that
range base will fit properly under
bracket.
To mount anti-tip bracket to concrete
or ceramic floor or wall, use a masonry
drill bit to drill XI" holes at each mounting
screw location. Tap plastic anchors into
mounting holes in floor or wall.
Floor Damage
l
Contact a qualified floor
covering installer for the best
procedure to drill mounting
holes through your type of floor
covering.
l
Before moving range across
floor, check that range is on
shipping base or slide range
.
il.
If installing the range in a mobile home,
you MUST secure the range to the floor.
Any method of securing the range is
adequate as long as it conforms to the
standards listed in the Mobile home
installation instructions, Panel A.
onto cardboard
or hardboard.
Failure to follow these instructions
may result In damage to floor
covering.
Line up holes in anti-tip bracket with
holes in floor or wall. Use the screws
provided to mount the anti-tip bracket
to the floor or wall.
screw locailonr
7,
0
7-F
9.
Move range close to final position.
Remove shipping base, cardboard or
hardboard from under the range. Plug
power supply cord into grounded outlet.
To mount anti-tip bracket to wood floor
or wall, drill ,/,'I holes at the two mounting
screw locations where the two lines are
crossed by the third line.
Place rack in oven. Place
level on rack, first side to side;
then front to back. If range is not level at
the front, adjust the leveling legs up or
down until the range is level. If rear of
range needs adjusting, adjust rear
leveling legs up or dowh until range is
level. If rear legs are adjusted downward
more than 1/8:' add shims under anti-tip
bracket.
Note: Oven must be level for satisfactory
baking conditions.
Fire Hazard
Do Not make connection
too
tight. The regulator is die cast.
Overtightening
may crack the
regulator, resulting in a gas leak
and possible fire or explosion.
--Z-13.14.16.
'-'
AII
connections must be wrench-
tightened.
flexible connector
Numbers
correspond
to steps.
adapter
Yz" adapter
shutoff valve
pres++3
regularor
13
Remove cooktop.
H
Assemble the flexible
connector from the gas supply pipe to
the pressure regulator in this order:
manual shutoff valve, ,/," nipple,
,/," adapter, flexible connector,
1/2" adapter, and ,/," nipple.
14
Use pipe-joint compound
1
made for use with L.l? gas
to seal all gas connections. If flexible
connectors are used, be certain
connectors are not kinked.
'15
Open the shutoff valve in
n
the gas supply line. Wait
a few minutes for gas to move through
the gas line.
PANEL C