Whirlpool 626701 Instrukcja instalacji - Strona 4

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Okap wentylacyjny Whirlpool 626701. Whirlpool 626701 7 stron.

Drukuj stronę

terminal

bOX

cover

Remove terminal box Cover from

Mae than one person is required to help

with appliance

intiallation

because Of its

weight and size.

Failure to tallow these instructions may

result in personal injury.

Numbers

correspond

to steps.

To vent through wall with 3- 1 /A" X 10"

rectangular ductwork, measure from floor

65-7/r and 62-3/8" (or l/8" and 3-5/8" dOW

from underside of cabinet) and mark on

back wall, Measure and mark a line !5-1/4"

to right and left of centerline

connecting

'the two lines, Use a saber SUW t0 Cut a

rectangular

opening for the ductwork.

31,

Install ductwork through the vent opening in

upper

cabinei or wall. Complete venting

system according to method needed. See

*\/entina requirements. N Use caulking to

Lift the range hood into final

l position and center. Mark on the

nderside of cabinet the location of the

3 hole mounting slots. set IOn"* hnnrl

?k ,I protected surface.

four kc

aside L. ( - r

Ta wire through rear, mark a line 7-l /2" from

the right of the centerline on the Wall. Mark

the point on

this line that is 64-s/8" from the

floor (or I -3/8" from underside of cabinet).

Drill a T-1 /4" diameter hole through Wail at

this point'

,Kach rectangular damper to selectea

>.ctanguiar vent opening, If damper is

&ached to back of range hood, be Sure

jamper hinge is toward the top. Far round

ented installations, use round damper in

juct to prevent air from flowing back into

juclwork, If roof cap has a damper,

-'-.-rrh, k-'....Ac'^ Cm,-,-, rnnne hood,

Determine and clearly mark a vertical

centerline on the wall and cabinet in the

area the vent opening will be made.

To vent through the roof with 7" round

ducfwark

mark 4-l /2" and 5" in from back

wait atoni the centerline on underside Of

cabinet, Use these points as centers t0

draw 7-1 /g" circles on underside of cabinet.

Use a saber saw to cut the openings for the

ductwork

Repeat for the underside of the

top of the cabinet, This will create slotted

4 4

Run wiring through wall of cabinets

according to the National Electricai

Code

and local codes and ordinances.

DO Not

turn on power until installation is complete.

openings,

keyhole slot

To wire throl

To wire through top, mark a line 7-112" from

the righ.

_ "

the right of the centerline on the underside

of the c

of the cabinet, Mark the point on this tine

the

that is l-3/8" from back wall. Drill a 1-l /4"

diameter hole through the cabinet at this

die,..-.-.

Start screws through neck of each of the

four keyhole mounting screw slots marked

on the cabinet bottom,

point.

Lift

elc

the

Tic

,, _._-

ne-.. _

if used, rot&es up and down treW~

-range hood into final position, feeding

bctrical wire through wiring opening,

&ion the range hood so that the large

,d of the keyhole slots are over the screws,

en push the hood toward the wall SO that

e screws are in the neck of the SlOtS.

lhten mounting screws to cabinet,

oking sure mounting screws are in narrow

!ck of slots, Make sure that damper blade.

To vent through the roof with 3-j /4" X

rectangular ductwork, mark a line 1" and 5"

from the buck wall on the underside of the

cabinet

Mark lines 5-l /4" to the right and

left of the centerline on the underside of

cabinet that connect the lines just drawn.

Use a saber saw to cut a

EdangUlar

opening far the ductwork. Repeat for the

underside of the top of the cabinet,

Panel C