Whirlpool AKR 511 IX Instrukcja montażu i użytkowania - Strona 17
Przeglądaj online lub pobierz pdf Instrukcja montażu i użytkowania dla Okap wentylacyjny Whirlpool AKR 511 IX. Whirlpool AKR 511 IX 24 stron.
Drukuj stronę
Screw the two sections together with 6 screws (3 per
side).
15. Fix the upper flue set to the trellis near the ceiling with 6
screws (3 per side).
16. a.
Apply the lower/rear section (WITHOUT control
panel) to the rear part of the hood and pre-fix in
position with 2 screws (1 per side).
b. Apply the lower/front section (WITH control panel) to
the front part of the hood,
(b1) connect the electricity between the hood and
the control panel,
(b2) pre-fix in position with 2 screws (one per part),
c.
Fix the two sections of the lower sections of the flue
together, using 6 screws (3 per side. Also see the
diagram plan for coupling the two sections).
Note: If the two sections of the lower flue are NOT
perfectly aligned, try loosening all the screws, aligning
the sections of the lower flue and fastening the screws up
again.
17. Apply the 2 tabs (supplied) to cover the fixing points of the
bottom flue (CAUTION! THE BOTTOM FLUE TABS ARE
THE NARROWER AND SHALLOWER ONES).
The wider and deeper tabs are those used for the top flue,
and must be cut to size.
18. Turn the mains power on again at the central electrical
panel and check for correct hood operation.
Remount the carbon filter frame and the fat/s filter/s and check
the perfect functioning of the hood.
Description of the hood
Fig. 1
1. Control panel
2. Grease filter
3. Grease filter release handle
4. Halogen lamp
5. Vapour catcher
6. Telescopic chimney
7. Air outlet (used for filter version only)
Operation
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
Control panel
a.
maximum power selection aspiration switch
b.
medium power selection aspiration switch
c.
minimum power selection aspiration switch
d.
off aspiration switch
e.
on/off light switch
Maintenance
WARNING:
-
Use safety gloves.
-
Disconnect the appliance from the power supply.
Or if the appliance has been connected through a plug and
socket, then the plug must be removed from the socket.
Cleaning
WARNING:
-
Never use steam cleaning equipment.
-
Disconnect the appliance from the power supply.
The cooker hood should be cleaned regularly (at least with the
same frequency with which you carry out maintenance of the
fat filters) internally and externally. Clean using the cloth
dampened with neutral liquid detergent. Do not use abrasive
products. DO NOT USE ALCOHOL!
WARNING: Failure to carry out the basic cleaning
recommendations of the cooker hood and replacement of the
filters may cause fire risks.
Therefore, we recommend oserving these instructions.
The manufacturer declines all responsibility for any damage to
the motor or any fire damage linked to inappropriate
maintenance or failure to observe the above safety
recommendations.
Grease filter
Fig. 2
Traps cooking grease particles.
This must be cleaned once a month using non aggressive
detergents, either by hand or in the dishwasher, which must
be set to a low temperature and a short cycle. When washed
in a dishwasher, the grease filter may discolour slightly, but
this does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
Charcoal filter (filter version only)
Fig. 3
It absorbs unpleasant odours caused by cooking.
The charcoal filter can be washed once every two months
using hot water and a suitable detergent, or in a dishwasher at
65°C (if the dishwasher is used, select the full cycle function
and leave dishes out).
Eliminate excess water without damaging the filter, then
remove the mattress located inside the plastic frame and put it
in the oven for 10 minutes at 100° C to dry completely.
Replace the mattress every 3 years and when the cloth is
damaged.
Remove the filter holder frame by turning the knobs (g) 90°
that affix the chimney to the cooker hood.
Insert the pad (i) of activated carbon into the frame (h) and fit
the whole back into its housing (j).
17