Whirlpool UXT4836AAW Instrukcje instalacji oraz instrukcja obsługi i konserwacji - Strona 4
Przeglądaj online lub pobierz pdf Instrukcje instalacji oraz instrukcja obsługi i konserwacji dla Okap wentylacyjny Whirlpool UXT4836AAW. Whirlpool UXT4836AAW 28 stron. 30" (76.2 cm) and 36" (91.4 cm) range hood
Drukuj stronę
INSTALLATION REQUIREMENTS
s csnd
Gather the required tools and parts before starting installation.
Read and follow the instructions
provided with any tools listed
here.
Tools needed
•
Drill
•
1¼" (3.0 cm) drill bit
•
1/8"(3.0 mm) drill bit for pilot holes
•
Pencil
•
Wire stripper or utility knife
•
Tape measure or ruler
•
Caulking gun and weatherproof
caulking compound
•
Flat-blade screwdriver
•
Phillips screwdriver
For vented installations,
you also need:
•
Saber or keyhole saw
•
Vent clamps
•
Metal snips
•
Compass or 8" (20.3 cm) circle template
Parts supplied
Remove parts from package. Check that all parts are included.
•
Filter
•
4 - #10 x %" mounting screws
•
7" (17.8 cm) round transition plate
•
7" (17.8 cm) damper/vent
connector
•
31/4 '' x 10" (8.3 x 25.4 cm) damper/vent
connector
Parts needed
For direct wire installation
•
UL listed or CSA approved 1/2"(12.5 mm) strain relief
•
Two 40-watt maximum incandescent
light bulbs
•
Power supply cable (if needed, for direct wire installation)
For power supply cord installation
•
UL Listed Power Supply Cord Connection
Kit marked for
range hood use.
•
Two 40-watt maximum incandescent
light bulbs
For vented installations you also need:
•
31/4"x 10" (8.3 x 25.4 cm) or 7" (17.8 cm) round metal venting
•
7" (17.8 cm) round damper, if using 7" (17.8 cm) round vent
system
For cabinets with recessed bottoms:
•
Two 2" (5.1 cm) wide filler strips. Length and thickness
determined
by recess dimensions.
•
Four flat head wood screws or machine screws with washers
and nuts (to attach filler strips).
IMPORTANT." Observe all governing codes and ordinances.
•
It is the installer's responsibility
to comply with installation
clearances specified on the model/serial rating plate. The
model/serial
rating plate is located inside the range hood on
the rear wall.
•
Range hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
•
Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance. Consult the
cooktop/range
manufacturer
installation instructions
before
making any cutouts.
•
Grounded electrical outlet is required. See "Electrical
Requirements"
section.
•
The hood is factory-set
for vented installations.
For non-
vented (recirculating) installations, charcoal filter pad Part
Number 4396846 is available from your dealer.
•
All openings in ceiling and wall where range hood will be
installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured
Home Construction
Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction
and Safety, title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured
Home
Installation 1982 (Manufactured
Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local
codes.
Product Dimensions
1 1/2"
(2.5 cm)
6"J
(15.2=cm)