AER COMPACT 60 2 Instrukcja obsługi - Strona 6

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Wzmacniacz do instrumentów muzycznych AER COMPACT 60 2. AER COMPACT 60 2 8 stron. Amplifier
Również dla AER COMPACT 60 2: Podręcznik użytkownika (10 strony)

Drukuj stronę
AER COMPACT 60 2 Instrukcja obsługi

5. Technical Data

Inputs
Input (channel 1) Stereo jack ¼" (6.35 mm)
High impedance, unbalanced jack input for
instruments (pick-ups) and line-level sources.
high/low switch: –10 dB attenuator
Impedance: 2.2 Meg
Input (channel 2) Combo socket, XLR jack ¼" (6.35 mm)
line mode:
High impedance, unbalanced jack input for
instruments (pick-ups) and line-level sources.
Sensitivity: 38 mV
Impedance: 1 Meg
mic mode:
XLR (balanced), stereo jack (balanced),
or mono jack (unbalanced) input.
Voice Filter
24 V-Phantom-Power through 6.8 kohms
to XLR socket
Clip indicator: Headroom 6 dB
Return
Return from external parallel effect loop
Sensitivity: 430 mV
Clip
Headroom: 15 dB
Attack Time: 4 ms
Outputs
(note 3)
Phones
Headphones output. When connected, internal
speakers are muted.
Stereo jack, ¼" (6.35 mm)
Output power: 100 mW
Caution: For stereo headphones with stereo jack
plug only. Do not connect mono plugs.
Tuner
Tuner output. Mono jack, ¼" (6.35 mm)
Output voltage: 310 mV
Line out
Line output after tone controls,
with return and effects.
Mono jack, ¼" (6.35 mm).
Output Voltage: 1.3 V
DI-out
Line output after tone controls,
with return and effects.
Mono jack, ¼" (6.35 mm).
Output Voltage: 1.3 V
Send
Send for parallel effect loop
Mono jack, ¼" (6.35 mm)
Output voltage: 1.3 V
6
Tone controls
channel 1: ± 8 dB at 100 Hz
Bass
channel 2: ± 8 dB at 100 Hz
channel 1: ± 6 dB at 800 Hz
Middle
Treble
channel 1: ± 8 dB at 10 kHz
channel 2: ± 11 dB at 10 kHz
Effects
Internal effect
digital effect processor with 4 factory presets
1 – warm hall
2 – bright hall
3 – chorus with reverb
4 – flanger
External effect
Parallel effect loop (see send and return)
Power
Power amp
60 W at 4 ohms,
discrete bipolar transistor design
Analog signal
Subsonic filter, low distortion RMS limiter
processing
Speaker system 8" (200 mm) twin cone speaker
Mains power
AC 230 V, 50-60 Hz, max. 120 W
(other mains voltage available)
Mains fuse
slow 1 A for 230-240 V
slow 2 A for 115 V
slow 2 A for 100 V
General
Cabinet
15 mm (0.6") finnish birch plywood
Finish
Waterbased acrylic, choco spatter finish
Dimensions
265 mm (10.4 ") high
330 mm (13 ") wide
235 mm (9.25 ") deep
Weight
7,55 kg (16.65 lbs)
Notes:
Input levels refer to 50 Watts output.
Output levels refer to 50 mV input at channel 1.
Specifications and appearance subject to change without notice.