AER domino 3 Podręcznik użytkownika - Strona 3

Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Wzmacniacz do instrumentów muzycznych AER domino 3. AER domino 3 8 stron.
Również dla AER domino 3: Podręcznik użytkownika (16 strony), Podręcznik (18 strony)

Drukuj stronę

2. Safety Precautions

The following guidelines shall help minimize the risk of injury through

fire or electric shock.

1. Carefully read these safety notes before you use the device!

2. Keep these safety notes in a safe place.

3. Pay attention to all warnings, instructions and additional texts on

the unit.

4. Do not install or use your amp in close proximity to water or if you

are wet yourself.

5. Use your amp in a safe place where nobody can step on cables or

trip over and damage them.

6. Pay attention to an unhindered air circulation around the amp,

never obstruct the air vents or grilles.

7. Always pull the mains plug before cleaning your amp. Use only a

dry cloth for cleaning. Avoid the use of detergents and do not let

any liquids seep into the unit.

3. Controls and Connections

Front panel top

(from left to right):

channel 1/2/3/4

input

XLR/6.3 mm jack plug combi socket

pad

Input sensitivity selector switch

pressed = lower sensitivity

line/mic

Signal source selector switch.

line: For instruments (pickups),

only via jack plug.

mic: For microphones with a jack or an

XLR connector.

gain

Input level control

clip

This indicator lights up when overload is immi-

nent in the respective channel.

9 V

This indicator lights up when the 9 V phantom

power is turned on.

(As a factory default setting the 9 V phantom

power is only available on channel 1&3. See

also operation summary).

48 V

This indicator lights up when the 48 V phantom

power for condenser microphones is turned on

(See also operation summary).

colour

This switch activates the midrange contour fil-

ter. Boosts presence and slightly cuts midrange

frequencies.

8. Use only the right fuses with the same current rating and trigger

characteristic as replacements. Never mend fuses! Pull the mains

plug before replacing a fuse. Should a fuse blow again after a

short while, the device needs to be checked.

9. Never install your amp close to devices with strong elec-

tromagnetic fields such as large mains transformers, revolving

machines, neon illumination etc. Do not lay signal cables parallel

to power current cables.

10. There are no user-servicable components inside the unit. To avo-

id the risk of an electric shock, the unit must not be opened. All

maintenance, adjustment and repair works should be carried out

by qualified staff only. Any unauthorized tampering will void the

2-year warranty.

11. In keeping with the EMV regulations screened cables with cor-

rectly fitted connectors must be used for all signal connections.

12. Always use an earthed power supply with the correct mains volta-

ge. If you are in doubt about the power outlet's ground, have it

checked by a qualified technician.

13. Cable up your amp only when it is powered off.

mute

Channel mute switch

bass

Bass control

middle

Midrange control

treble

Treble control

eff. send

Adjusts the effects send level for the corre-

sponding channel (the internal effect

is blended).

effect select ch 1/2 Rotary control for effect selection

on channel 1&2

effect select ch 3/4 Rotary control for effect selection

on channel 3&4

aux in

Adjusts the signal level at the aux in

jack sockets

eff. level

Master level control for all internal effects

pre out

Adjusts the signal level at the L-out ‚

and R-out jacks

master

Adjusts the overall volume level

power

This LED indicates that your amplifier

is ready to use