Bad Cat The Leash Instrukcja obsługi - Strona 2
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Jednostka sterująca Bad Cat The Leash. Bad Cat The Leash 2 stron.
Również dla Bad Cat The Leash: Instrukcja obsługi (2 strony), Instrukcja obsługi (2 strony)
Drukuj stronę
Operation
The Leash is easy to use. Just follow these simple steps for years of trouble-free service. Your equipment should be "OFF" while connecting. Plug your
amplifier into the jack marked "AMP" and your speaker into the jack marked "SPEAKER". Now, turn on your amplifier. The In/Out switch is true-bypass.
There is a small amount of insertion loss when switching the device "In" (typically1db). Set the Ohms selector to match the output impedance of your
amplifier and the Ohms rating of your speaker. Using a mismatched load will result in degraded performance. For best results in any case, always match
the Ohms selector to the amplifier. To help with Ohms calculation, the two speaker jacks are wired in parallel (for use with additional cabinets). The
large knob on the front controls your overall balance between speaker load, from whisper quiet to maximum loudness. The Leash dissipates unused
audio power by converting it to heat. An AC power cord operates a cooling fan located at the top of the housing. This fan allows The Leash to operate at
maximum efficiency under all playing conditions. To prevent damage to The Leash or your amplifier, it is absolutely essential that the onboard cooling
fan be operating whenever The Leash is in use.
IMPORTANT!
LIMITED LIFETIME WARRANTY
FOR YOUR PROTECTION, PLEASE READ
THE FOLLOWING:
Bad Cat Amplifiers warrantees our amps and cabs against workmanship or defect for
WATER AND MOISTURE: Appliance should
life. The warrantee does not cover tubes or cosmetic damage, or wear and tear or abuse.
not be used near water (near a bathtub,
This warrantee is transferable. Lifetime transferable warranty is only for North American
washbowl, kitchen sink, laundry tub, in a
sales. Please see your local dealer and distributor for warranty information. Modifying or
wet basement, or near a swimming pool,
altering the amp in any way voids the warrantee. Shipping to and from the warranty repair
etc). Care should be taken so that objects
center is the responsibility of the customer.
do not fall and liquids are not spilled into
the enclosure through openings.
We have a new Lifetime Warranty on all new amps leaving the factory. We are extending
POWER SOURCES: The appliance should
the Lifetime Warranty to all of our pre acquisition amps for $249. Simply send the unit
back to us and we will have one our technicians go through it from the ground up. And to
be connected to a power supply only of
the type described in the operating in-
top it all off, we will pay for the shipping back to you. For more information please contact
structions or as marked on the unit.
us at [email protected] or directly at 800-730-0966.
When RETURNING merchandise to the factory, you must call for a return authorization
GROUNDING OR POLARIZATION: Precau-
tions should be taken so that the ground-
number.
ing or polarization means of an appliance
is not defeated.
HELP SECTION
POWER CORD PROTECTION: Power sup-
1) AMP WILL NOT TURN ON
ply cords should be routed so that they
Check the power to the amp. Check for tripped circuit breakers, unplugged extension
are not likely to be walked on or pinched
cords or power-strip switches that may be turned off. Check the fuse. If a dark brownish
by items placed upon or against them,
color or no wire can be seen within the glass tube, then replace. The amp may be perfectly
paying particular attention to cords at
fine but occasionally a fuse may blow because of high AC voltage surges. After the fuse
plugs, convenience receptacles, and the
has been replaced with the proper Slow Blow value and if the fuse fails again, the amp
point where they exit from the appliance.
will require servicing.
SERVICING: The user should not attempt
2) NO OUTPUT with POWER light ON
to service the unit beyond that described
Tubes damaged in shipping will be the primary reason for your amp to not function
in the operating instructions. All other
properly. Please give us a call to help guide you through this simple repair.
servicing should be referred to qualified
3) KEEP YOUR AMP LOOKING NEW
service personnel.
Use a damp cloth to wipe the controls on the front & rear chassis panels. Wipe the black
vinyl covering with a damp cloth.
FUSING: If your unit is equipped with a
fuse receptacle, replace only with the
same type fuse. Refer to replacement
text on the unit for correct fuse type.
This symbol is intended to alert
This symbol is intended to
the user to the presence of
alert the user to the presence
uninsulated "dangerous
of important operating and
voltage" within the product's enclosure that
maintenance (servicing) instructions in the
may be of sufficient magnitude to constitute
literature accompanying the appliance.
a risk of electric shock to persons.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL!
THIS UNIT CONTAINS HIGH VOLTAGE INSIDE!
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
PHONE 800.730.0966
FAX 714.630.0106
WWW.BADCATAMPS.COM
140 Technology Drive Suite 500, Irvine CA 92618
BAD CAT HOLDINGS LLC. USA