XBOX 360 Instrukcja demontażu

Drukuj stronę

Please note that these instructions describe how to disassemble your

Xbox. For most upgrades, modifications, and repairs you will not need to

completely disassemble your Xbox, therefore, parts 6 and 7 are optional.

It is also recommended that you read the instructions completely before

starting, so that you can understand better the purpose of each step.

Tools needed for Xbox 360 disassembly:

T6: To remove hard drive screws

T8: To remove internal Xbox 360 screws

T10: To remove Xbox 360 internal chassis from case

Metal Bar: To remove grey grills on ends of case

Micro Flat Screwdriver: To undo the clips which will separate

the case halves

Basic Disassembly:

Part 1: Preparation

Part 2: Removing the faceplate

Part 3: Removing the grey end grills

Part 4: Separating the case halves

Part 5: Removing the top half of the case

Advanced Disassembly:

Part 6: Removing the power switch

Part 7: Disassembling the hard drive

P P a a r r t t 1 1 : : P P r r e e p p a a r r i i n n g g y y o o u u r r X X b b o o x x 3 3 6 6 0 0

1) Remove any game discs from your Xbox 360.

2) Unplug the console from the wall.

3) Remove the hard drive and put it in a safe place. See Part 7 for

disassembly instructions for the hard drive.

4) Place your Xbox 360 in the horizontal position.

5) Make sure you have a good work area, with a place to put the

screws so that you do not lose them, and a place to put the various

case parts where they will not get scratched. You may want to

put a soft cloth underneath the case.

P P a a r r t t 2 2 : : R R e e m m o o v v i i n n g g t t h h e e f f a a c c e e p p l l a a t t e e

6) With your right hand, put your thumb in the USB door, and push

to the right (outside edge) of the case. Using your left hand,

squeeze the top and bottom of the faceplate. The faceplate will

pop off. See the arrows in the picture for exact locations.

X X b b o o x x 3 3 6 6 0 0 d d i i s s a a s s s s e e m m b b l l y y i i n n s s t t r r u u c c t t i i o o n n s s

Page 1 of 2

P P a a r r t t 3 3 : : R R e e m m o o v v i i n n g g t t h h e e g g r r e e y y e e n n d d g g r r i i l l l l s s

7) The grey grills are held on by 6 grey tabs. These must be

removed before you can separate the case halves. A view from

the inside of the case is shown in the picture. You must push the

clips shown from the outside so that they will slide over the

pegs that hold them in place.

8) Start with the grill that would be on the bottom of the case (when

the case is horizontal), the one that has the rubber feet on it.

9) Using the metal rod supplied, poke through the vent holes as

shown in the picture and push the grey tabs inward while

pulling upward on the grill. It may be useful to use one of the

other L keys to "hook" the grey grill and pull up.

10) Remove all 6 grey tabs. Pull the grill out and place it to the side.

11) Next remove the tabs from the top grill. With this grill, you

may need to remove the foot on the top rear of the case (when

Xbox is standing upright), there will be a hole underneath that

you can stick the rod through. If you do not want to remove the

foot (because of fear of losing it, because it will not stick as

well once removed and reapplied), you can leave the grill

attached by that one tab and move on to Part 4. You can

remove the final tab with your fingers after you separate the

case halves, but you will have to be careful not to bend it or

break it as it will be in the way.