Xerox Nuvera 100 Podręcznik planowania - Strona 11

Przeglądaj online lub pobierz pdf Podręcznik planowania dla Serwer druku Xerox Nuvera 100. Xerox Nuvera 100 20 stron. Production system
Również dla Xerox Nuvera 100: Arkusz specyfikacji (2 strony), Funkcje Podręcznik (34 strony), Podręcznik planowania (22 strony), Podręcznik użytkownika (40 strony), Instrukcja obsługi (34 strony), Podręcznik referencyjny (2 strony), Podręcznik referencyjny (42 strony), Skrócona instrukcja obsługi (2 strony), Instrukcja instalacji (2 strony), Podręcznik uzupełniający (48 strony), Podręcznik planowania (38 strony), Podręcznik planowania (16 strony), Podręcznik referencyjny (2 strony), Specyfikacje (2 strony), Podręcznik wskazówek i porad (18 strony), Podręcznik wskazówek i porad (18 strony), Podręcznik dla początkujących (26 strony), Podręcznik dla początkujących (30 strony)

Drukuj stronę
Xerox Nuvera 100 Podręcznik planowania
Lasermax Roll System DocuSheeter with optional Grain Rotator

Electrical Requirements

Environmental Requirements

Estimated Installation Time

Operating Supplies

Device
North America
DocuSheeter DP/DT
100-120 VAC 50/60 Hz, 6A
Cutter
100-120 VAC 50/60 Hz, 5A
Grain Rotator
Grain Rotator receives
power from the Cutter.
Sheet Transport
Sheet Transport receives
power from the Cutter.
Temperature
Humidity
Heat Emission
Sound Emission
Altitude
Lasermax Roll Systems personnel install the DocuSheeter at the
customer site. Estimated installation time is 8 hours, assuming
the following:
•
The Xerox printer to which the DocuSheeter DP will be
attached is installed and operational upon the arrival of the
Lasermax Roll Systems technician.
•
A small supply of appropriate paper rolls is available, to
assist in the installation process and to run initial production.
Note: For pre-printed rolls (run on the DocuSheeter DP equipped
with the print register option), rolls must conform to the Lasermax
Roll Systems document, "Print Registration Mark Specification".
In addition to installation time, the Lasermax Roll technician will
train customer personnel in the operation of the DocuSheeter
DP. Up to three two-hour operator-training sessions per system
type are standard. Each session can accommodate up to four
people. Training must occur in the two consecutive business
days after installation. Weekend, holiday and other shift
personnel should be trained in these sessions or additional
training arrangements can be made at additional charge.
The system does not come with a paper roll, and only comes
with a roll cart if one is ordered. There are no operating supplies
for the DocuSheeter.
1-5
Europe
220-240 VAC 50/60 Hz, 4A
220-240 VAC 50/60 Hz, 2.5A
Grain Rotator receives power
from the Cutter.
Sheet Transport receives
power from the Cutter.
Recommended: 72° ± 4° F (22° ± 2.4° C)
Minimum: 60° F (15° C)
Maximum: 80° F (27° C)
Recommended: 40% to 60% RH (non-condensing)
Unwinder: 632 BTU/hour (157 kcal/hour)
Cutter: 2000 BTU/hour (504 kcal/hour)
Grain Rotator: 3242 BTU/hour (817 kcal/hour)
All modules meet 90 dbA noise exposure limit
N/A