Yamaha Clavinova CLP-840 Instrukcja obsługi - Strona 26
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Instrument muzyczny Yamaha Clavinova CLP-840. Yamaha Clavinova CLP-840 40 stron. Clavinova
Drukuj stronę
Using the Recorder
RECORDER
"I"
"~1
0
2
DO
START!
~D
RECORDER
J:o
STOP
RED
GJD
~
I
'2
_
L,;;,o'
'-1
' 1
~
"~1:""
To play back what you've recorded, first make sure that the green track
indicators of the tracks you want to play are lit. If not, press the corresponding
track button(s) so that they are lit. Then press the RECORDER [START!
STOP] button. Playback starts from the beginning of the recorded data, and
will stop automatically at the end of the recorded data. You can also stop
playback at any time by pressing the [START/STOP] button.
To mute a track so that it doesn't play back, press the corresponding track
button so that its indicator goes out (press again to tum the track back on).
The current measure number appears on the display during playback.
n~rNOTfJ
.
It
is
possible to play along on the keyboard during playback. In this case, the
playback voice and the voice you play on the keyboard are not the same. The
playback voice
is
the voice that was set when the data was recorded. The voice
you play on the keyboard
is
the voice that
is
selected on the panel.
• The playback volume and tempo can be adjusted by using the [MASTER VOL
UME] control and [TEMPO
~/,A]
buttons (press both [TEMPO
~/,A]
buttons
simultaneously to recall the default tempo).
• All recorder data will be retained in memory for about one week after the power is
turned off. If you want to keep your recorded data for longer periods, tum the power
on for
a
few minutes at least once
a
week. It
is
also possible to store it to an
external MIDI storage device such
as
the Yamaha MIDI Data Filer MDF3 by using
the Bulk Data Dump function described on page 36.
• The track indicators wilJ not light automatically when the power
is
turned on even if
the recorder contains data. It is therefore necessary to press the track buttons
so
that the corresponding green indicators light before starting RECORDER playback.
It
is
also
a
good idea to press the track buttons to check if the tracks contain data
before recording. If the green indicator lights when the corresponding track button
is pressed, that track contains data which will be erased and replaced by the
newly-recorded data.
• If
the metronome
is
being used during playback, the metronome will automatically
stop when playback
is
stopped.
• During recorder playback, the volume of
a
track which
is
turned off will always be
"0" (i.e. the "Piano Song Part Cancel Volume" function - page
33
only affects
piano song playback.
• The playback data
is
not transmitted via the MIDI OUT connector.
• Playback cannot be started when the demo/piano song mode
is
engaged.
• Playback cannot be started when the recorder contains no data, or when both track
buttons are off.
• When using REVERB or EFFECT during playback, depending upon the conditions
one reverb type and one effect type will take priority.
D
Synchro Start ....................................................................................................................
When the Synchro Start function is engaged, recorder playback will begin
automatically as soon as you start playing on the keyboard.
To engage the Synchro Start function press the [START/STOP] button
while holding a track button which is ON. The rightmost dot on the display will
flash at the current tempo. (Repeat the previous operation to disengage the
Syncro Start function.) Playback will then start as soon as you begin playing on
the keyboard.
If you hold a track button which is OFF while pressing the [START/STOP]
button, that track will be turned ON and the Synchro Start mode will be engaged.