Yamaha YPP-35 Instrukcja obsługi - Strona 12

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Instrument muzyczny Yamaha YPP-35. Yamaha YPP-35 21 stron. Personal electronic piano
Również dla Yamaha YPP-35: Instrukcja obsługi (21 strony), Instrukcja obsługi (20 strony), Instrukcja obsługi (20 strony), (francuski) Tryb zatrudnienia (20 strony)

Drukuj stronę

The following chart shows the relation between

YPP-35 voices and MIDI Program Numbers.

MIDI Program Number

| YPP-35 Voice/Voice Select Button

MIDI Control Number

оон

РІАМО 1

01H

PIANO 2

02H

E. PIANO

03H

HARPSICHORD

04H

VIBES

05H

STRINGS

06H

CHOIR

07H

PIPE ORGAN

This relation applies to both transmission and reception.

MIDI Program Numbers other than those in the chart

cannot be transmitted or received.

Cancelling Program Change Message

Program Change message is automatically available

when the YPP-35 is turned on. Though it is a very

useful feature, you may sometimes run into a situ-

ation where you wish to cancel it. To cancel Program

Change message, while holding down the МИ

TRANSPOSE button, press the Voice Select button

PIANO 2. To reactivate this message, repeat the

same procedure.

2) Control Change Message

Control Change message deals with various aspects

of the played sound.

For instance, when you're

using the YPP-35 as a Master, and you depress the

foot switch, a Control Change message (including

МО! Control Number and a Damper value) will be

transmitted, and the Slave's sound will also be

sustained (unless it cannot receive the message). If

the YPP-35 is the Slave, it will receive Control

Change messages from the Master. The YPP-35,

as a Master, can transmit only Damper information

(MIDI Control Number 64 in the following chart). As

a Slave, however, it can receive a lot more infor-

mation, as shown in the chart below:

YPP-35 Control Change Message

Reception Capabilities

Name

Value

Volume (*1)

0-127

Expression (*1)

0-127

Damper

0:Off, 1-127:0n

(Variable)

Local On/Off (*2) | 0:Off, 1-127:Оп

А! Notes Off (*3)

Omni Off (*4)

Omni On (*4)

(*1)Volume/Expression:

The volume of the YPP-

35 will be adjusted internally regardless of its panel

setting, according to the Control Change message it

receives. For instance, if the YPP-35 receives a "0"

value message for volume/expression, it will not

produce a sound even if its own VOLUME slider is

set to the MAX position.

(*2)Local On/Off: Upon reception of a Local ОН

message, the YPP-35's keyboard will be separated

from its internal sound module. See "Example 3" оп

page 12 for details.

(*3)All Notes Off: As soon as the YPP-35 receives

this instruction, all of its notes sounding at that time

will be muted.

(*4)Omni Off/On: See the following section, "MIDI

Channels", for details.

Cancelling Control Change Message

Normally, Control Change message is automatically

available when the YPP-35 is turned on. But you

may wish to create a situation where, for example,

the Slave YPP-35 sounds are not sustained in

tandem with the Master sounds.

To cancel the

Control Change message, while holding down the

MIDI/TRANSPOSE button, press the Voice Select

button E. PIANO.

То reactivate this message,

repeat the same procedure.

The above-described Note On, Program Change,

and Control Change messages are known as MIDI

channel information.

That is, these messages are

communicated through MIDI channels. So whatare

MIDI channels?

The next section addresses this

question.

| Па

БІН