Yamaha Electone HS-8 Instrukcja obsługi - Strona 7

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Klawiatura elektroniczna Yamaha Electone HS-8. Yamaha Electone HS-8 20 stron. Serie hs monitor da studio alimentato e subwoofer alimentato
Również dla Yamaha Electone HS-8: Instrukcja obsługi (2 strony), Instrukcja obsługi (2 strony), Instrukcja obsługi (20 strony), Instrukcja obsługi (20 strony), Instrukcja obsługi (21 strony), Instrukcja obsługi (20 strony), Instrukcja obsługi (20 strony), Instrukcja obsługi (20 strony), Instrukcja obsługi (20 strony), Instrukcja obsługi (20 strony), Instrukcja obsługi (20 strony), Instrukcja obsługi (20 strony), Instrukcja serwisowa (43 strony), (Angielski) Instrukcja obsługi (20 strony)

Drukuj stronę

HS8S (Subwoofer)

Subwoofer Connections

1 INPUT L/R connector

These connectors receive the input signal to the

subwoofer. Balanced XLR and balanced phone jack

connectors are provided for both the L and R inputs.

The L and R inputs can be used simultaneously.

Signals supplied to both the L and R inputs are mixed

internally.

NOTE The XLR and phone jack input connectors can not be

used simultaneously. Use only one input connector at a

time.

NOTE Refer to "Connectable cables" on page 5 for more

connector details.

Connectin the Subwoofer to the

HS8/HS7/HS5 Speakers

2 OUTPUT L/R connectors

These are the subwoofer's output connectors.

The input signals received at the INPUT L and R

connectors are output via the OUTPUT L and R

connectors, respectively. Low frequency reproduction

characteristics can be adjusted via the LOW CUT

switch and LOW CUT control.

3 LOW CUT switch

When this switch is ON, the low frequencies are

attenuated prior to output via the OUTPUT L and R

connectors at the frequency set by the LOW CUT

control. The low-frequency attenuation cutoff

frequency can be adjusted via the LOW CUT control.

4 LOW CUT control

Adjusts the low-frequency attenuation cutoff

frequency between 80 Hz and 120 Hz when the LOW

CUT switch is ON.

4 5

HS8S

si nal flow

Subwoofer Response Control

5 HIGH CUT control

Sets the cutoff frequency for subwoofer output high-

frequency attenuation from 80 Hz to 120 Hz.

6 PHASE switch

Switches the phase of the subwoofer output.

This switch should be set to [NORM.] in most

situations, but in combination with some speakers

and in some speaker layouts switching to the [REV.]

setting may improve low-frequency response. Select

the setting that provides the best bass response in

your system.

7 LEVEL control

Adjusts the subwoofer output level.

8 Power switch

Turns power to the subwoofer ON or OFF.

Rock the switch to the right [

the left [

panel will light when the power is ON.

NOTICE

• Turning the power switch ON and OFF in rapid succession can cause

the device's electronics to malfunction. Please wait for 3 seconds or

more after turning the power OFF before turning it ON again.

• Even when the power switch is turned off, electricity is still flowing to

the product at the minimum level. When you are not using the product

for a long time, make sure to unplug the power cord from the wall AC

outlet.

9 AC IN connector

Connect the supplied power cable here. First connect the

power cord to the subwoofer, then insert the power cord

plug into the AC outlet.

] to turn the power ON, or to

] to turn the power OFF. The logo on the front

HS8/HS7/HS5/HS8I/HS7I/HS5I/HS8S Owner's Manual

6 7