aerauliqa Quantum AX Instrukcja instalacji - Strona 3
Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Wentylator aerauliqa Quantum AX. aerauliqa Quantum AX 15 stron. Dmev unit
Również dla aerauliqa Quantum AX: Instrukcja instalacji (18 strony)
Drukuj stronę
lasso di tempo regolabile, per poi tornare alla velocità minima selezionata (oppure alla
velocità media in caso di funzionamento automatico tramite umidostato). Il LED frontale
indica che l'interruttore esterno è acceso. La funzione timer si attiva solo se l'interruttore
esterno è rimasto acceso per almeno 60 secondi.
Funzionamento con interruttore pull cord integrato (versione HTPC): collegamento come
fig. 14D. Quando l'interruttore pull cord è attivato, il ventilatore funziona alla velocità
massima (Boost). Spegnendo l'interruttore pull cord, il ventilatore continua a funzionare
alla velocità massima per un lasso di tempo regolabile, per poi tornare alla velocità
minima selezionata (oppure alla velocità media in caso di funzionamento automatico
tramite umidostato). Il LED frontale indica che l'interruttore pull cord è attivato. La
funzione timer si attiva solo se l'interruttore è rimasto acceso per almeno 60 secondi.
SETTAGGIO TIPO dI INSTALLAZIONE
La tipologia di installazione può essere selezionata tramite il JUMPER 1 tra le seguenti
opzioni: espulsione diretta o canalizzata (fig. 16).
SETTAGGIO VELOCITA' MINIMA CONTINUA
La velocità minima continua può essere selezionata tramite il JUMPER 2 e il JUMPER 3
tra le seguenti opzioni: 21, 29, 47 m
4
/h oppure off (fig. 16).
3
G
Installation manual
Quantum AX- dMEV unit
Read this manual carefully before using the product and keep it
in a safe place for reference.
This product was constructed up to standard and in compliance
with regulations relating to electrical equipment and must be
installed by technically qualified personnel.
The manufacturer assumes no responsibility for damage to persons
or property resulting from failure to observe the regulations contained
in this booklet.
PRECAUTIONS FOR INSTALLATION, USE ANd MAINTENANCE
• T he device should not be used for applications other than those specified in this manual.
• A fter removing the product from its packaging, verify its condition. In case of doubt,
contact a qualified technician. Do not leave packaging within the reach of small children
or people with disabilities.
• D o not touch the appliance with wet or damp hands/feet.
• T his appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
• D o not use the product in the presence of inflammable vapours, such as alcohol,
insecticides, gasoline, etc.
• I f any abnormalities in operation are detected, disconnect the device from the mains
supply and contact a qualified technician immediately. Use original spare parts only for
repairs.
• T he electrical system to which the device is connected must comply with regulations.
• B efore connecting the product to the power supply or the power outlet, ensure that:
- the data plate (voltage and frequency) correspond to those of the electrical mains
- the electrical power supply/socket is adequate for maximum device power. If not,
contact a qualified technician.
• T he device should not be used as an activator for water heaters, stoves, etc., nor
should it discharge into hot air/fume vent ducts deriving from any type of combustion
unit. It must expel air outside via its own special duct.
• O perating temperature: 0°C up to +50°C.
• T he device is designed to extract clean air only, i.e. without grease, soot, chemical or
corrosive agents, or flammable or explosive mixtures.
• D o not leave the device exposed to atmospheric agents (rain, sun, snow, etc.).
• D o not immerse the device or its parts in water or other liquids.
• T urn off the main switch whenever a malfunction is detected or when cleaning.
• F or installation an omnipolar switch should be incorporated in the fixed wiring, in
accordance with the wiring regulations, to provide a full disconnection under overvoltage
category III conditions (contact opening distance equal to or greater than 3mm).
• I f the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
• D o not obstruct the fan or exhaust grille to ensure optimum air passage.
• E nsure adequate air return into the room in compliance with existing regulations in
order to ensure proper device operation.
Fig. 1
5