Yamaha CX-A5200 Instrukcja obsługi - Strona 18

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Wzmacniacz Yamaha CX-A5200. Yamaha CX-A5200 28 stron. Av
Również dla Yamaha CX-A5200: Przykład połączenia (2 strony)

Drukuj stronę
Yamaha CX-A5200 Instrukcja obsługi

Advanced speaker configuration

Caution
• Remove the unit's power cable from an AC wall outlet before making any connections or operating the
switches.

Using a speaker that supports bi-amp connection

If you want to use a speaker that supports bi-amp connection to have more high-quality sounds,
change the CH. SELECTOR setting and connect the speaker to the corresponding pair of the
SPEAKERS terminals.
(Example)
Using a speaker that supports bi-amp connection for CH.3 (R)
The unit (rear)
SPEAKERS
R
CH.6
REAR
PRESENCE
CH.5
CH.3 A (R) and
SURROUND
CH.4 (R) terminals
CH.4
BRIDGE
(
)
FRONT
PRESENCE
BRIDGE
A
(
)
CH.3
FRONT
B
CH.2
SURROUND
BACK
CH.1
CENTER
By setting the CH. SELECTOR for CH.4 (R) to "CH.3", CH.3 (R) input signals are output from both the
CH.3 A (R) and CH.4 (R) speaker terminals. In this case, CH.4 (R) input is not used.
Caution
• Before making bi-amp connections, remove any brackets or cables that connect a woofer with a tweeter.
Refer to the instruction manual of the speakers for details. If you are not making bi-amp connections, make
sure that the brackets or cables are connected before connecting the speaker cables.
Input from pre-amplifier
TRIGGER
+12V
CH.5
CH.3
SURROUND
FRONT
IN
R
R
THROUGH
OUT
CH.6 AMP ASSIGN
CH.4 AMP ASSIGN
CH.2
CH.3
OUT
CH.5
CH.3
BRIDGE
CH.1
12V 0.1A
CH.3
CH.3
BRIDGE
CH.6
CH.4
REAR
FRONT
AUTO POWER
PRESENCE
PRESENCE
STANDBY
R
R
OFF
ON
IMPEDANCE
SELECTOR
CH.4
Set CH. SELECTOR for
CH.4 (R) to "CH.3"

Making a Bridge Connection Between the Front Speakers

You can enjoy high-powered sound by bridging the front speakers.
To make a bridge connection, set the CH. SELECTOR for CH.4 (L/R) to "CH 3 BRIDGE", and then
connect speakers to the CH.3 A (L/R) and CH.4 (L/R) speaker terminals.
The unit (rear)
SPEAKERS
R
CH.6
REAR
PRESENCE
CH.5
SURROUND
CH.3 A (R) and
CH.4 (R) terminals
BRIDGE
CH.4
(
)
FRONT
PRESENCE
BRIDGE
A
(
)
CH.3
FRONT
B
CH.2
SURROUND
BACK
CH.1
CENTER
Caution
• When using a bridge connection, the +/- terminals of CH.3 B as well as the - terminals of CH.3 A and CH.4
cannot be used.
Input from pre-amplifier
TRIGGER
+12V
CH.5
CH.3
IN
SURROUND
FRONT
R
R
THROUGH
OUT
CH.6 AMP ASSIGN
CH.4 AMP ASSIGN
CH.2
CH.3
OUT
CH.5
CH.3
BRIDGE
CH.1
12V 0.1A
CH.3
CH.3
BRIDGE
CH.6
CH.4
REAR
FRONT
AUTO POWER
PRESENCE
PRESENCE
STANDBY
R
R
OFF
ON
IMPEDANCE
SELECTOR
CH.4
Set CH. SELECTOR for
CH.4 (R) to "CH.3 BRIDGE"
Advanced speaker configuration
19
En