Yamaha DXR8 Podręcznik - Strona 12
Przeglądaj online lub pobierz pdf Podręcznik dla System głośników Yamaha DXR8. Yamaha DXR8 12 stron. Dxr and dxs series powered speakers and subwoofers
Również dla Yamaha DXR8: Instrukcja obsługi (22 strony), Instrukcja obsługi (22 strony), Instrukcja obsługi (22 strony), (Angielski) Instrukcja obsługi (22 strony), (Angielski) Instrukcja obsługi (22 strony), (Rosyjski) (22 strony)
Drukuj stronę
Specifications
DXR8
DXR10
General
System Type
2-way, Bi-amp powered speaker, Bass-reflex type
Frequency Range (-10dB)
57Hz – 20kHz
56Hz – 20kHz
Coverage Angle
H90° x V60° constant directivity horn
Crossover Type
FIR-X tuning™ (Linear phase FIR filter)
Crossover Frequency
2.4kHz
2.3kHz
Measured Maximum SPL (peak)
129dB SPL
131dB SPL
IEC noise@1m
Transducer
LF
Diameter
8" cone
10" cone
2"
2"
Voice Coil
Magnet
Ferrite
HF
Diaphragm
1.4"
Type
1" throat compression driver
Magnet
Ferrite
Enclosure
Material, Finish, Color
ABS, Matte black
Floor Monitor Angle
–
50°
280 x 458 x 280 mm
305 x 502 x 310 mm
Dimensions
(W x H x D, with rubber feet)
(11" x 18" x 11")
(12" x 19-3/4" x 12-2/8")
Net Weight
13.5kg (29.8lbs)
14.6kg (32.2lbs)
Handles
Aluminium die-cast (Top x 1)
Pole Socket
35mm with 2-way feature (0 or 7 degrees)
Rigging Points
Top x 2, Rear x 1
(Fits for M8 x 15mm eyebolts)
Optional Accessory (U-bracket)
UB-DXR8
UB-DXR10
Amplifier
Amplifier Type
Class-D
Power Rating*1
Dynamic
1100W (LF: 950W, HF: 150W)
Continuous
700W (LF: 600W, HF: 100W)
Cooling
Fan cooling, 4 speeds
AD/DA
24bit 48kHz sampling
Signal Processing
48bit (Accumulator: 76bit)
HPF/LPF
OFF, 100, 120Hz 24dB/oct HPF
DSP Preset
D-CONTOUR: FOH/MAIN, MONITOR, OFF
Clip limiting, Integral Power Protection, DC-fault
Protection
Speaker
Amplifier
Thermal, Output over current
Power Supply
Thermal, Output over voltage, Output over current
Connectors
Input
INPUT1: XLR3-31 x 1, INPUT2: Phone x 2,
INPUT3: RCA PIN x 2
THRU: XLR3-32 x 1 (Parallel with INPUT1),
Output
LINK OUT: XLR3-32 x 1
Input
LINE: 12kΩ, MIC: 8kΩ
INPUT1
Impedance
INPUT2, 3
L, R: 40kΩ, MONO: 20kΩ
Input Sensitivity
INPUT1
LINE: +1dBu, MIC: -32dBu
(LEVEL: Maximum)
INPUT2, 3
-13dBu
Input Sensitivity
INPUT1
LINE: +11dBu, MIC: -22dBu
(LEVEL: Center)
INPUT2, 3
-3dBu
Maximum Input
INPUT1
LINE: +24dBu, MIC: +20dBu
Level
+16dBu
INPUT2, 3
Controls
LEVEL x 3, LINE/MIC, HPF, D-CONTOUR, FRONT LED DISABLE, LINK MODE, POWER
Idle Power Consumption
35W
1/8 Power Consumption
90W
Power Requirements
100V – 240V, 50Hz/60Hz
0dBu is referenced to 0.775Vrms.
*1 Power rating (120V, 25°C). This is total value of individual output power.
DXR12
DXR15
DXS12
Powered subwoofer, Band-pass type
52Hz – 20kHz
49Hz – 20kHz
47Hz – 160Hz
–
–
2.1kHz
2.1kHz
–
132dB SPL
133dB SPL
131dB SPL
12" cone
15" cone
12" cone
2.5"
2.5"
2.5"
–
–
–
Wood, Paint, Black
50° Symmetrical
50° Symmetrical
–
362 x 601 x 350 mm
445 x 700 x 380 mm
397 x 563 x 594 mm
(14-1/4" x 23-5/8" x 13-3/4")
(17-1/2" x 27-1/2" x 15")
(15-5/8" x 22-1/8" x 23-3/8")
19.3kg (42.5lbs)
22.5kg (49.6lbs)
33.0kg (72.8lbs)
Aluminium die-cast (Side x 2)
Metal (Side x 2)
35mm (Top x 1)
Top x 2, Rear x 1
–
(Fits for M10 x 18mm eyebolts)
UB-DXR12
UB-DXR15
–
Class-D
950W
600W
80, 100, 120Hz 24dB/oct LPF
D-XSUB: BOOST, XTENDED-LF, OFF
INPUT: XLR3-31 x 2
THRU: XLR3-32 x 2 (Parallel with INPUT)
10kΩ
–
+1dBu
–
+11dBu
–
+24dBu
–
LEVEL, POLARITY, LPF, D-XSUB,
FRONT LED DISABLE, POWER
110W
120W
Specifications
Specifications
DXS15
General
System Type
45Hz – 160Hz
Frequency Range (-10dB)
Coverage Angle
Crossover Type
Crossover Frequency
132dB SPL
Measured Maximum SPL (peak)
IEC noise@1m
Transducer
15" cone
LF
Diameter
2.5"
Voice Coil
Magnet
HF
Diaphragm
Type
Magnet
Enclosure
Material, Finish, Color
Floor Monitor Angle
478 x 618 x 624 mm
Dimensions
(18-7/8" x 24-3/8" x 24-1/2")
(W x H x D, with rubber feet)
38.0kg (83.8lbs)
Net Weight
Handles
Pole Socket
Rigging Points
Optional Accessory
Amplifier
Amplifier Type
Power Rating*1
Dynamic
Continuous
Cooling
AD/DA
Signal Processing
HPF/LPF
DSP preset
Protection
Speaker
Amplifier
Power Supply
Connectors
Input
Output
Input
Impedance
Input Sensitivity
(LEVEL: Maximum)
Input Sensitivity
(LEVEL: Center)
Maximum Input
Level
Controls
Idle Power Consumption
1/8 Power Consumption
Power Requirements
DSR112
DSR115
DSR215
2-way, Bi-amp powered speaker, Bass-reflex type
55Hz - 20kHz
45Hz - 20kHz
45Hz - 20kHz
H90° x V60° constant directivity horn
FIR-X tuning™ (Linear phase FIR filter)
1.7kHz
134dB SPL
136dB SPL
138dB SPL
12" cone
15" cone
2 x 15" cone
3"
2.5"
Neodymium
Ferrite
2"
1" throat compression driver
Neodymium
Wood, LINE-X®, Black
50°
–
–
370 x 638 x 368mm
442 x 755 x 423mm
467 x 1158 x 520mm
(14-9/16" x 25-1/8" x 14-1/2")
(17-3/8" x 29-3/4" x 16-5/8")
(18-3/8" x 45-9/16" x 20-1/2")
21.2kg (47lbs)
28.0kg (62lbs)
49.8kg (110lbs)
Metal (Top x 1)
Metal (Side x2)
35mm (Bottom x 1)
–
Top x 2, Rear x 1
–
(Fits for M10 x 18mm eyebolts)
–
Class-D
1500W (LF: 1020W, HF: 480W)
1300W (LF: 850W, HF: 450W)
Natural convection
24bit 48kHz sampling
48bit (Accumulator: 76bit)
OFF, 120Hz 24dB/oct HPF
D-COUNTOR(Dynamic CONTOUR)
Clip limiting, Integral Power Protection, DC-fault
Thermal, Output over current
Thermal, Output over voltage, Output over current
XLR-3-31 x 1
TRS Phone Jack x 1
XLR-3-32 x 1
Parallel with INPUT
LINE: 12kΩ, MIC: 8kΩ
LINE: 0dBu, MIC: -25dBu
LINE: +7dBu, MIC: -18dBu
LINE: +24dBu, MIC: -11dBu
LEVEL, LINE/MIC, HPF, D-CONTOUR, FRONT LED DISABLE, POWER
30W
100W
140W
North America: 120V, 60Hz, Japan: 100V, 50Hz/60Hz, Other areas: 220 - 240V, 50Hz
DSR118W
Powered subwoofer, Bass-reflex type
40Hz - 130Hz
–
–
–
132dB SPL
18" cone
3"
Ferrite
–
–
–
–
520 x 638 x 584 mm
(20-1/2" x 25-1/8" x 23")
42.0kg (93lbs)
35mm (Top x 1)
–
1020W
800W
120Hz 24dB/oct LPF
–
XLR-3-31 x 2
XLR-3-32 x 2
Parallel with INPUT
10kΩ
0dBu
–
–
–
+24dBu
LEVEL, POLARITY,
FRONT LED DISABLE, POWER
100W