Yamaha YST-SW005 Instrukcja serwisowa - Strona 2
Przeglądaj online lub pobierz pdf Instrukcja serwisowa dla System głośników Yamaha YST-SW005. Yamaha YST-SW005 16 stron. Yamaha subwoofer system owner's manual
Również dla Yamaha YST-SW005: Instrukcja obsługi (20 strony), Instrukcja obsługi (19 strony), Instrukcja serwisowa (13 strony)
Drukuj stronę
YST-SW005
TO SERVICE PERSONNEL
1. Critical Components Information
Components having special characteristics are marked s
and must be replaced with parts having specifications equal
to those originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
from supply circuits.
Meter impedance should be equivalent to 1500 ohm shunted
by 0.15µF.
Leakage current must not exceed 0.5mA.
Be sure to test for leakage with the AC plug in both polarities.
WARNING: CHEMICAL CONTENT NOTICE!
The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and /or plastic
(where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency
(and possibly other entities) to cause cancer and/or birth defects or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA-
SON WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose
eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.
SPECIFICATIONS
Type .......... Advanced Yamaha Active Servo Technology
Output Power
J, U, C models ............ 55 W/100 Hz, 5 Ω 10% T.H.D.
R, T, K, A, B models ... 50 W/100 Hz, 5 Ω 10% T.H.D.
Input Sensitivity
INPUT 1 (SP) ....................................................... 0.7 V
INPUT 2 (PJ) ...................................................... 30 mV
Input Impedance
INPUT 1 (SP) ..................................................... 2.2 kΩ
INPUT 2 (PJ) ....................................................... 12 kΩ
Frequency Response
Driver
Input Section
INPUT 1 ............................................. Speaker terminal
INPUT 2 ................................................... RCA pin jack
Power Supply
J model ........................................... AC100V, 50/60Hz
U, C models ........................................ AC120V, 60Hz
R, T, K models .......... AC110/120/220/240V, 50/60Hz
A model ............................................... AC240V, 50Hz
B, G models ........................................ AC230V, 50Hz
1
Ω
(100 Hz, 50 W/5
, L+R)
30 Hz–200Hz
................ 16 cm (6.5") cone
magnetic shielding type
WALL
EQUIPMENT
OUTLET
UNDER TEST
INSULATING
TABLE
Power Consumption
U, C, R, T, K, A, B, G models ............................. 60 W
J model ................................................................ 32 W
Standby Power Consumption
Dimensions
(W x H x D) ..... 200 x 365 x 375 mm
Weight
................................ 8.5 kg (18 lbs. 12 oz.)
Finish
Black color / Cherry color ......................... All models
Silver color .............................................. U, C models
Accessory
U, C, R, T, K, A, B, G models ........... Nonskid Pad x 4
J model
U ........ U.S.A. model
A ........ Australian model
G ........ European model
T ........ Chinese model
J ......... Japanese model
Specifications are subject to change without notice due
to product improvements.
AC LEAKAGE
TESTER OR
EQUIVALENT
..... 0.8 W
(7-7/8" x 14-3/8" x 14-3/4")
C .... Canadian model
B .... British model
R .... General model
K .... Korean model