Zanussi ZOS78964XU Podręcznik użytkownika - Strona 42
Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Piekarnik Zanussi ZOS78964XU. Zanussi ZOS78964XU 49 stron.
Drukuj stronę2. Pull the front end of the shelf support away
from the side wall.
3. Pull the supports out of the rear catch.
Install the shelf supports in the opposite sequence.
STEAM CLEANING
Remove as much dirt as possible manually.
Remove the accessories and the shelf support to
clean the side walls.
The steam cleaning functions support the steam
cavity cleaning of the oven.
Before you start a cleaning procedure, make sure
that the oven is cool.
When the steam cleaning function works, the light
is off.
1. Fill the water drawer to the maximum level
(around 950 ml of water) until a signal sounds
or the display shows the message.
2. Choose the steam cleaning function in the
menu: Cleaning.
Steam Cleaning - the duration of the function
is around 30 minutes.
a) Turn on the function.
b) When the programme ends a signal
sounds.
c) Press a sensor field to turn off the signal.
Steam Cleaning Plus - the duration of the
function is around 75 minutes.
a) Spray a suitable detergent uniformly in the
oven cavity on both enamel and steel parts.
b) Turn on the function.
The first part of the programme ends after
around 50 minutes.
c) Press
.
Follow the message in the
display to complete the
cleaning.
d) Wipe the cavity of the oven with a non-
abrasive surface care sponge. You can use
warm water or oven detergents.
e) Press
.
The final part of the procedure starts. The
duration of this stage is around 25
minutes.
3. Wipe the cavity of the oven with a non-abrasive
sponge. You can use warm water.
After cleaning keep the oven door open for
approximately 1 hour. Wait until the oven is dry. To
speed up the drying you can heat up the oven with
hot air at temperature 150 °C for approximately 15
minutes. You can get maximum effects of the
cleaning function if you manually clean the oven
immediately after the function ends.
42
CLEANING REMINDER
When reminder is displayed cleaning is necessary.
Use the function Steam Cleaning Plus.
You can enable / disable the function: Cleaning
Reminder in the menu: Basic Settings.
STEAM GENERATION SYSTEM - DESCALING
When the steam generator operates, limestone
accumulates inside it (because of calcium contents
in the water). This can have a negative effect on the
steam quality, on the performance of the steam
generator and on the food quality. To prevent
limestone accumulation, clean the steam generation
circuit.
Remove all accessories.
Select the function from the menu: Cleaning. The
user interface will guide you through the procedure.
The duration of the complete procedure is about 2
hours.
The light in this function is off.
1. Make sure that the water drawer is empty.
2. Press
.
3. Put the grill- / roasting pan on the first shelf
position.
4. Press
.
5. Put 250 ml of the descaling agent in the water
drawer.
6. Fill the remaining part of the water drawer with
water to the maximum level until the signal
sounds or the display shows the message.
7. Press
.
This activates the first part of the procedure:
Descaling.
The duration of this part is around 1
hour 40 minutes.
8. After the end of the first part, empty the grill- /
roasting pan and put it on the first shelf
position again.
9. Press
.
10. Fill the water drawer with fresh water to the
maximum level until the signal sounds or the
display shows the message.
11. Press
.
This activates the second part of the procedure:
Descaling. It will rinse the steam generation circuit.
The duration of this part is around 35
minutes.
Remove the grill- / roasting pan after the end of the
procedure.