Alecto Hesdo DBX-90 Instrukcja obsługi - Strona 7

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Elektroniczna niania Alecto Hesdo DBX-90. Alecto Hesdo DBX-90 7 stron.

Drukuj stronę

11.Each time a button is pressed, a beep tone will be heard to validate your entry

being recognized by the unit.

12.The loudness of the alarm and beep tone is fixed and independent from adjustment

of the speaker volume.

Both the receiver and transmitter can be carried around using the belt clip. To remove

the clip, follow diagram as shown.

PRECAUTIONS

• Use only the supplied AC adapters, use of other adapters may cause damage to the

DBX-90 baby monitor

• When not using the monitor for as long period of time, remove all batteries from

the transmitter and receiver to avoid damage due to battery leakage.

• Disconnect the AC adapter from the wall outlet when the monitor is not to be

operated.

• The DBX-90 is best performed within a temperature range of -9˚C to +50˚C .

• Do not leave the monitor expose to strong sunlight for a long time or nearby any

heat source, moisture and excessive dusty environment.

• Do not open the cabinet, no serviceable part inside.

STANDARD ACCESSORIES

a. 6V AC adapter for transmitter

b. 9V AC adapter for rapid charger

c. Rapid charger

d.Transmitter unit

e. Receiver unit

f. 4.8V rechargeable Ni-mH battery pack

g.User manual

TROUBLE SHOOTING GUIDE

Problem

Possible Causes

Transmitter has no

- Mic sensitivity is too low

transmission

- Battery has run down or AC

adapter improperly connected

Transmitter always on

- Mic sensitivity is too high

Out-of-range alarm

- Channel or digital code setting

always on

is different in transmitter and receiver

- Transmitter' s battery has run down

- Out-of-range alert setting in

transmitter is Off but setting in

receiver is On

- Distance between transmitter and

receiver exceeds the operating range

Out-of-range alarm

- Interference from other devices

sometimes on

operating on same channel

No Out-of-range alarm

- Setting of Out-of-range alert in

both transmitter and receiver is Off

- Setting of Out-of-range alert in

transmitter is On but in receiver

is Off

Temperature alarm

- The upper and lower temperature

always on

limit is set too close to the

current reading

Always showing low

- Battery has run down

battery alert

- No battery inside receiver

- Battery pack is damaged

Battery life is short

- Night light is permanently

switched on

- Vibration alert is switched on

Many static noise

- Transmitter is located near other

and interference

electrical appliances

Too short

- Many steel structures between

communication

transmitter and receiver

range

- Output power in transmitter

is set to Lo

- Transmitter battery has run down

- Transmitter's range check is

set to On.

Solution

- Adjust mic sensitivity higher

using up/down button 2

- Replace with new battery or

check connection

- Adjust mic sensitivity lower using up/down

button 2 such that transmitter become

voice activated

- Set the same channel and digital code

in both transmitter and receiver

- Replace with new battery or use AC adapter

- Change Out-of-range alert setting in

transmitter to On

- Move the transmitter and receiver closer

together

- Switch to another channel

- Change both settings to On

- Change setting in receiver to On

- Set the upper and lower temperature limit

around 5˚C difference from current reading

- Recharge battery using charger stand

(receiver). Replace with new battery or use

AC adapter (transmitter)

- Put battery pack back into battery

compartment.

- Replace with new battery pack

- Switch off night light or set to

VOX operate

- Switch off vibration alert

- Remove the electrical appliances or re-locate

the transmitter far away from source of

interference or change to another channel

- Re-locate transmitter or receiver

- Change output power setting to Hi

- Replace with new battery or use AC adapter

- Set range check function to off.