Directed Xpresskit DBALL2 Instrukcja instalacji - Strona 10

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Przez blokady Directed Xpresskit DBALL2. Directed Xpresskit DBALL2 13 stron. Ford5 remote start ready (rsr) installation
Również dla Directed Xpresskit DBALL2: Instrukcja instalacji (12 strony), Instrukcja instalacji (19 strony), Instrukcja instalacji (18 strony), Podręcznik (14 strony), Instrukcja instalacji (14 strony), Instrukcja instalacji (19 strony), Instrukcja instalacji (16 strony), Instrukcja instalacji (20 strony), Instrukcja instalacji (15 strony), Instalacja i skrócona instrukcja obsługi (16 strony), Instrukcja instalacji (18 strony), Instrukcja instalacji (16 strony), Instrukcja instalacji (18 strony), Instrukcja instalacji (16 strony), Podręcznik (19 strony)

Drukuj stronę

Directed Xpresskit DBALL2 Instrukcja instalacji

Platform: DBALL2

Firmware: CHRYSLER6

LED Diagnostics and Troubleshooting

LED

Status

Module Programming

Off

Solid

Solid red

red

Green &

Green & Red

red

Flashes

Flashes green

green

Flashes orange

slowly

Solid green then

Solid green

then orange

orange for 3 secs.

x 3 secs

Solid orange for 3

Solid orange x

3 secs

seconds.

Solid green x

Solid green for 3

3 secs

seconds

Module Programming - Error codes

Flashes red

Flashes red x 2

x 2

Flashes red

Flashes red x 3

x 3

External module synchronization

Flashes red,

Flashes red, red

red & orange

x 10 secs

then orange, x 10

Active Ground While Running

Flashes

Flashes green

green

Flashes red &

Flashes

red &

orange

Flashes

Flashes green

green

quickly

D2D and W2W Commands

Flashes

Flashes orange x 1

orange x 1

Flashes

Flashes orange x 2

orange x 2

Description

Module has no power.

Waiting to begin the

programming sequence.

Initialization failed.

Module is programming.

Ready for Key2GO programming.

Bypass was skipped.

Module was successfully

programmed without bypass.

Module was successfully

programmed.

CAN C not detected.

Bypass data not detected.

OBDII feature not supported.

GROUND OUT ON (GWR)

command received.

IGNITION ON command received.

START ON command received.

LOCK command received.

UNLOCK command received.

Troubleshooting

Make sure the D2D harness is connected or that the 12

Volt is present between the red and balck wires. If the

12 Volt is present, the module be be defective.

Check if the ignition input is properly connected.

If a second attempt fails after a complete Hard Reset,

connect the module to Directechs.com and call Tech

Support with the module ID in hand.

Make sure that the bypass connections are correct (see

wiring diagram).

Normal operation.

Check the CAN connections

Check the bypass line connection. If more than one wire

is used, make sure they are not inverted. Start vehicle

using the key to confirm the OEM equipment is still

operational.

Diagnostic data bus not detected. Some features are

not supported by SmartStart. This can be caused by

missing wire connections or module hardware limitation.

Refer to the wiring installation section to check the

connections.

Otherwise, the Ground While Running (status) signal

was lost or was never received by the module.

Commands can come from RF, D2D or W2W.

Otherwise, the ignition signal was not received by the

module. In a W2W install, it will show only if the ignition

input wire is used.

Otherwise, the start signal was not received by the

module. In a W2W install, it will show only if the ignition

input wire is used.

If the bypass module fails to flash, it means the module

did not receive the signal.

Rev.: 20151029

Page 10