Directed Xpresskit DBALL2 Instrukcja instalacji - Strona 8

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Przez blokady Directed Xpresskit DBALL2. Directed Xpresskit DBALL2 19 stron. Ford5 remote start ready (rsr) installation
Również dla Directed Xpresskit DBALL2: Instrukcja instalacji (12 strony), Instrukcja instalacji (19 strony), Instrukcja instalacji (18 strony), Podręcznik (14 strony), Instrukcja instalacji (13 strony), Instrukcja instalacji (14 strony), Instrukcja instalacji (16 strony), Instrukcja instalacji (20 strony), Instrukcja instalacji (15 strony), Instalacja i skrócona instrukcja obsługi (16 strony), Instrukcja instalacji (18 strony), Instrukcja instalacji (16 strony), Instrukcja instalacji (18 strony), Instrukcja instalacji (16 strony), Podręcznik (19 strony)

Drukuj stronę

Directed Xpresskit DBALL2 Instrukcja instalacji

Platform: DBALL2

Firmware: CHRYSLER7 Remote Start Ready Installation (RSR)

Module Programming

Refer to the LED Diagnostics section on page 13 for more information and for troubleshooting purposes.

Important

Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to

ensure everything is correct prior to moving onto the next step.

Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper feature and

function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest

version of the application.

Warning!

To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app.

Flashing a module using your computer:

1. Connect the interface module to your computer using the

XKLoader2.

2. Go to www.directechs.com using Internet Explorer, and

select the Config for RSR button.

3. Follow the instructions to select your vehicle, installation

type, and configure your options.

4. Once you have configured the firmware options, click on the

FLASH button.

When the flashing operation is successful, you can proceed with the programming instructions below.

SmartStart Installation

The DBALL module must be disconnected from any power source before SmartStart can

be connected to it. Failing to do so could damage DBALL.

To ensure that the D2D communication between SmartStart and DBALL works properly, the

Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue

loop must be cut (Rev A SmartStart).

Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by

the DBALL D2D connector.

Connect SmartStart to DBALL using the D2D port.

XL202 Installation

Connect XL202 to DBALL using the D2D port.

Connect the 10-pin, 12-pin and 14-pin harnesses to

DBALL, then wait until the LED turns ON solid red.

Remove the battery from the factory keyless remote

Use the tip of the remote to press on the Start/Stop button (PTS) twice

to turn the ignition ON ("RUN" illuminates on Start/Stop switch).

The LED flashes green.

Press on the Start/Stop button (PTS) once to turn the ignition OFF.

Flashing a module using your smartphone or tablet

1. Connect the interface module to your XKLoader3.

2. Launch the Directechs Mobile app on your smartphone or

tablet.

3. Select FLASH YOUR MODULE and follow the on screen

instructions.

Go to the next page to complete the module programming.

SmartStart

XL202

Open

and

remove battery

to ON

ENGINE

(RUN)

START

STOP

PUSH x2

PUSH x1

ENGINE

START

STOP

to OFF

Rev.: 20160610

Page 8

Solid

Flashes