ABB Relion 620 Series Skrócona instrukcja obsługi - Strona 2
Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Urządzenie zabezpieczające ABB Relion 620 Series. ABB Relion 620 Series 4 stron.
Drukuj stronę
2
Q U I C K S TA R T G U I D E R E L I O N ® 6 2 0 S E R I E S
—
Using the local HMI
Accessing main menu and local authorization
Press
to navigate between main menu, measurements
and multiple single-line diagram pages.
If the local authorization has been enabled you must login
before entering the menu. To login press
level with
or
. Confirm the selection with
password one digit at the time using
next digit with
or
. Confirm the password with
cancel using
. To logout press
Changing parameters
Press
and select which setting value you want to change
and press
to change it with
mark at the same line with parameter value, you have to first
select which setting group parameter you want to change.
If there is no "#" mark you can change the value directly by
pressing
and then select value with
keys. Confirm the selection with
parameters they have to be stored to get them into use.
Storing settings
Store the settings by going back to main menu by pressing
or using the
key. When IED asks confirmation to commit
changes, answer "Yes". Some changes require the IED to reboot
before the changes can be taken into use. Reboot the IED by
Menu → Configuration → General → Software reset
going to
or switching the auxiliary power off and back on.
Changing the overcurrent start value
Menu → Settings → Settings →
→ Current Protection → PHLPTOC1 → Start value
and press
Clearing events and indications
There are two ways to do this:
• Go to clear menu by pressing
the main menu. Then select what you want to clear and
press
, press
(Clear text will appear and Cancel will
disappear) and then press
• Press
hold for three seconds to clear indications and
immediately after that three seconds again to clear LEDs.
Checking IED order code, serial number, HW revision
and software version
Menu → Information → Product Identifiers
Display header area
The icon area at the upper right corner of the dislay shows
the current action or user level. These are described below:
S = Parameters are being stored, ! = Warning and/or indication
V = Viewer, O = Operator, E = Engineer, A = Administrator
and select user
. Enter the
or
and moving to
or
again.
or
keys. If there is "#"
or
and
or
. After making changes to
setting group, default 1
select
or selecting
Clear
from
.
Using the function buttons
The function buttons can be configured as control buttons.
Configurations can be made with PCM600. Check the function
button action from the label, before pushing the button.
The action will take effect immediately when the button
is pressed.
If function buttons are set to follow L/R restriction, the control
must be set to Local for button to execute.
Monitored data
Menu → Monitoring
From here you can find a lot of information about the present
status of IED and monitored data. For example physical input
and output states, GOOSE counters, the states and I/O data
of the function blocks and the counter values of MMS vertical
communication. You can also find recorded data including
the currents and voltages of the latest faults.
Checking IED status (IRF)
Menu → Monitoring → IED Status → Self-supervision
Changing the default view
Menu → Configuration → HMI → Default View
Changing the display contrast
Hold
and press
or
If you want to store the contrast, go first in the menu and then
go back to the default view, so that A (Administrator) appears
to the right upper corner. If authentication is enabled you need
to login and then change the contrast.
Changing the language
Menu → Language
or you can push
the menu and language will be changed. English is always the
default language and there can be maximum of two additional
languages in the IED.
Changing function block naming from IEC 61850 names
to IEC 60617 or ANSI
Menu → Configuration → HMI → FB Naming convention
Complete customer documentation is available in the product
pages that can be accessed through abb.com/relion.
to change the display contrast.
and
anywhere in