CTEK MXS 10 Podręcznik użytkownika - Strona 3
Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Ładowarka do akumulatorów samochodowych CTEK MXS 10. CTEK MXS 10 7 stron. Fully automatic
Również dla CTEK MXS 10: Podręcznik użytkownika (2 strony), Podręcznik (6 strony), Instrukcja obsługi (20 strony)
Drukuj stronę
CHARGING PROGRAMS
Sellings are made by pressing the
MODE-bullan.
After about two seconds the
charger
activa
tes the
selected
program.
The
selected
program will be restarted next time the
charger is
connected.
The table e
x
plains the
different
Char
ging
Programs:
RECOND
Batter
.
1mm1•11111~!..lltt'ftlh.J.
i
20-300Ah
Normal
batte
ry program
14.4V/10A. Use for WET
batteries,
Co/Co,
MF
and for most GEL batteries
-2o·
c-+so·c
(·4°f-122°F)
AGM battery progrom
14.7V/10A
1-2o·c-+so•c
Use
for AGM
batteries.
(·4°F-122°f)
Recond p rogrom
15.8V/1.5A
Use to return energy to
the
empty
WET
and Co/Co
batteries.
Recond
your
battery
once
per
yeor ond ofter
deep dischore to maximise lifetime
and
capacity.
The Recond
program
odds STEP
6
to the
n
o
rmol bott
e
ry
prog
ram.
frequent use of
the
Recond
program may
cause
waler
loss
in
the
batteries
and reduce service life
of
electronics. Contocl your
vehicle
and
battery
supplier for
advice.
-2o·c-+so·c
(-4°f-122°F)
E
Supply program
13.6V/10A
Use as 12V power
supply
or use for
Root maintenance charging when
100%
capacity of the
battery is
required.
Supply
program activates step
7
wilhout
time
or voltage limitation.
.2o·c-+so·c
(·4°f-122°F)
Ii\.
T~'(• sp~r~ p'U'l~~~~~~?~)o'''-~'Y
chory1._•r
Ii'
m
is
d,sobiC"d
dur1n9
SUPPLY program
m
4
•
EN
ERROR
LAMP
If the error lamp
is lit,
check the following:
11
1.
Is the
chargers pos itive
lead
connected
to
the
batterys
positive pole
?
2
.
11 the chare•r connect9cl
to
a 12V
battery?
3.
Has
char
g ing
b
e
en
In
t
errupte
d in STEP
1,
2
o
r
5?
Restart
the charger
by pressing the MODE-bullon. If charging is still
being interrupted,
the
battery
...
STEP
1:
...
is
seriosly sulphated ond
ma
y need
to
be
replace
d.
STEP
2
:
...
con not accept charge and may need lo be
replaced.
STEP 5:
...
con not keep charge and may need lo be replaced
.
POWER LAMP
If
the
power lamp
is lit
with a:
-
1.
STEADY LIGHT
The
mains cable is connected lo the wall sodcet.
2. FLASHING
LIGHT1
The charger hos enlefed the
~
10Ve
mode.
This
happens
ii
the
charger
isn
·1
connected
lo
the
botlery
in
2
minutes ~·
- --
TEMPERATURE SENSOR
The MXS 10
is
equipped with on external temperature
se
nsor. The
tempera-
ture sensor is attachable.
If so, the
charger will compensate voltage accor·
ding to
ambient
temperature.
Activoted temperature sensor
will
be
indicated
by
a
lit
temperature
sensor
indicator
lamp.
READY TO USE
The
table
shows the estimated lime
for
empty
batte
ry
lo
80%
charge
BATTERY SIZE (Ah)
20Ah
50Ah
100Ah
200Ah
TIME TO
80%
CHARGED
2h
5h
10h
20h