Nikon Forestry Pro Instrukcja obsługi - Strona 8

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Przyrządy pomiarowe Nikon Forestry Pro. Nikon Forestry Pro 19 stron.
Również dla Nikon Forestry Pro: Podręcznik użytkownika (48 strony)

Drukuj stronę

Operational Summary

Caution—use of controls or adjustments or

performance of procedures other than those

specified herein may result in hazardous radiation

exposure

1. Install a battery in the battery chamber. (See "Changing

Batteries")

2. Rubber eyepiece cup

Eyeglass wearer: Collapse the eyepiece cups.

Non-eyeglass wearer: Do not collapse the eyepiece cups.

3. Diopter adjustment

Adjust diopter to obtain a clear image in the LCD.

First, rotate the diopter adjustment ring counterclockwise

until it comes to a complete stop. Next, turn on the power

to activate the LCD when you look through the Nikon Laser

Forestry Pro. Rotate the diopter adjustment ring clockwise

until the display comes into focus.

If the diopter is not adjusted to correspond to your

eyesight, you may not be able to clearly focus your subject.

4. Measuring

Note: See the chapter "External and Internal display" for external

LCD panel.

Note: D epressing and holding down the POWER button causes

all symbols to be displayed in the internal LCD panel. After

you remove your finger from the POWER button, the last-

used setting is displayed. (If you briefly press the POWER

button then remove your finger, the LCD panel may

display the last-used setting without displaying all of the

symbols. This is not a malfunction or other problem.)

Before measuring, be sure to confirm settings, such as unit,

measurement/display mode and priority mode.

◎

: See the relevant mode section in this manual for setting.

POWER

LCD is illuminated

◎

Set your desired modes

☆

Align the reticle

with the target

For continuous

distance and angle

measurement (up

POWER

to 20 seconds), keep

button depressed.

appears

MODE

※

Indication

Results are converted

remains

to the mode set and

illuminated for

displayed.

30 sec.

30 seconds pass without operation ＊

Power off: LCD indications disappear

※ See the the chapter "External and Internal display" for

details regarding the operations and results display of the

various modes."

＊ Power turns off 30 seconds after the last operation.

☆【Continuous measurement mode】

Keeping the POWER button depressed allows you to

perform continuous measurement for 20 seconds.

Blinks while performing measurements.

When measuring a pin at a golf course, for example, use First

Target Priority and Continuous measurement mode for easy

measurement. With no objects between you and the pin, the

smallest number is the distance to your targeted pin.

5. Selecting display unit (Factory default setting is feet.)

Yard

Feet

Meter

[

]

[ ]

[

]

1. Confirm the LCD panel is on.

2. Press and hold the

MODE

button for approx. two seconds.

3. When display unit has switched, release the

MODE

button.

4. Repeat steps 2 and 3 until your desired mode is displayed.

5. W hen you have completed setting, results will be converted

and displayed in the your selected measurement unit.

6. Switching measurement/display modes (Factory default

setting is linear distance measurement mode)

Linear Distance [

]

Horizontal Distance [

Height [

]

Angle [

]

Vertical Separation

Three-point measurement

(height between 2

[

]

[

]

points )

By pressing the MODE button, modes will change in the order

indicated above.

1. Confirm the LCD panel is on.

2. Press MODE button within 0.5 seconds.

3. Release MODE button to switch the mode.

4. Repeat steps 2 and 3 until your desire mode is displayed.

5. Switching the mode after measurement converts the

results to the new mode.

6. After the mode is set, measurements are performed in the

new mode.

]