Cub CB-1034 Instrukcja szybkiej instalacji - Strona 4

Przeglądaj online lub pobierz pdf Instrukcja szybkiej instalacji dla Czytnik kodów kreskowych Cub CB-1034. Cub CB-1034 4 stron.

Drukuj stronę

Performing Media Calibration

Once you have loaded the ribbon and labels as shown above it will be necessary to

perform a media calibration. The media calibration allows the printer to determine what

size label has been loaded and if a ribbon is being used. Failure to calibrate the printer

may cause errors such as NO PAPER, PAPER JAM & NO RIBBON to be shown on the

printers LCD display.

Follow the steps below to perform a media calibration.

1. Make sure the ribbon and label media are installed properly as described above.

2. With the printer power off press and hold the printer's

3. Power the printer on. Do not release the

display reads Calibrating.

4. The Printer will advance several labels, feeding the last label to the label

perforation. Once completed the printer's LCD display will read Ready.

5. Should there be any errors on the LCD display please see the troubleshooting

section of the users guide.

Printer Self-Test

To verify the printer is functioning correctly it is best to print a printer self-test. The

self-test can be performed after the media calibration is complete and before installing

the printer on your host PC. Follow the steps below to perform a self-test.

1. Install ribbon and label media and successfully perform media calibration.

2. Press the

button on the printer's front panel.

3. Press the

DOWN

button until

4. Press the

SELECT

button.

Print Config.

will now be highlighted, press SELECT. The printer will now print a

self-test label.

6. Press the

DOWN

button until

SELECT

button.

7. Press the

DOWN

button until

SELECT

button. The printer's LCD display should now read Ready.

8. Please note that the self-test is pre-formatted to print on a 4 inch wide label.

When using a smaller label some self-test information may run off the side of the

label and not print.

Your Cub CB-1024 is now ready to be installed on your host PC. Please see the

Installing Windows Print Driver guide to complete printer installation on your host PC.

This guide will also walk you through installing the provided Seagull Scientific BarTender

UltraLite label creation software.

**** More Information about your Cub CB-1024 can be found in

the User's Guide on the provided CB-1024 installation CD. ****

PAUSE

button.

PAUSE

button until the printer's LCD

Diagnostics

is highlighted.

exit

is highlighted once highlighted press the

exit

is highlighted once highlighted press the

Network Printing

The following steps are for network printing applications only. When connecting your

printer to the host PC via USB, parallel or RS-232C interfaces these steps do not apply.

Viewing Network Status

To view the current network settings follow the steps below.

1. Press the

button on the printer's front panel.

Setup

will now be highlighted press the printer's

3. Press the printer's

DOWN

button until

press the printer's

SELECT

button.

Status

will now be highlighted press the printer's

printer's Ethernet status.

IP Address

will now be highlighted press the printer's SELECT button to view the

printer's current IP Address, Subnet Mask and Gateway. To view the printer's

network card MAC Address press the printer's

is highlighted press the printer's

6. To return to the previous menu press the printer's

Configure: (DHCP / Static IP)

1. Follow steps 1-3 from viewing network status (above).

Status

will now be highlighted press the printer's

highlighted, once highlighted press the printer's

3. The printer will now display

DHCP

obtaining an IP address is DHCP. The printer will automatically use DHCP upon

power up to obtain an IP address. To turn DHCP off press the printer's

button while

DHCP

is highlighted. Press the printer's

will reboot and the DHCP method will be disabled.

4. To set the printer's Static IP address press the printer's

Static

IP. Once Static IP is highlighted press the printer's

can now enter the printer's IP Address, Subnet Mask & Gateway. To enter the

value press the printer's

button. To advance to the next number press the

printer's

DOWN

button. Once the value is entered press the printer's

button to advance to the next network setting.

entered press the printer's

SELECT

settings will be saved.

**** For more information regarding network setup please see

the user guide section 3.1.4. ****

SELECT

button.

Ethernet

is highlighted, once highlighted

SELECT

button to view the

DOWN

button, once

MAC Address

SELECT

button.

SELECT

button.

DOWN

button until

SELECT

button.

and

Static

IP. The printer's default method for

button, the printer

DOWN

button to highlight

SELECT

button. You

After all three values have been

button. The printer will reboot and your

Configure

SELECT