Disc Makers ReflexMax1 Skrócona instrukcja obsługi

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Duplikator płyt Disc Makers ReflexMax1. Disc Makers ReflexMax1 1 stron. Cd reflexmax series
Również dla Disc Makers ReflexMax1: Skrócona instrukcja obsługi (2 strony), Podręcznik użytkownika (9 strony), Podręcznik użytkownika (13 strony)

Drukuj stronę

ReflexMax1

BASIC OPERATION

THIS QUICK START GUIDE HAS BASIC INSTRUC-

TIONS FOR DUPLICATING DISC-TO-DISC, WHICH

IS COPYING CD-R

FROM A MASTER CD PLACED

IN THE REFLEXMAX1'S TOP DRIVE. FOR MORE

DETAILED INSTRUCTIONS ON THE

REFLEXMAX1'S DUPLICATING OPERATION,

PLEASE REFER TO THE USER'S GUIDE ON THE

ATTACHED CD.

1 Power on the ReflexMax1 by pressing the round

button located at the bottom right on the front of

the unit. The system will initialize and perform a

self-test, which will be shown on the LCD display.

2 When the self-test is complete, 1 Copy will

appear on the LCD display. Press the DOWN arrow

until 8 Select Source appears on the LCD display.

3 Press the ENT button and the following image

should appear on the display:

SRC: CD-ROM

01 IDE2 Slave

If the above image appears on the screen, hit ESC

and proceed to step 5.

4 If the above image does not appear on the

screen, press the DOWN arrow until it displays

SRC: CD-ROM 01 IDE2 Slave. Press the ENT but-

ton and the LCD will display CD-ROM selected.

Press ENT again.

5 Press the UP arrow until you return to 1 Copy.

™

CD-R Quick Start Guide

To start the duplication process, load the top drive

with your CD master. Load the bottom writer drive

with a high-quality blank CD-R or CD-RW.

6 Press the ENT button to begin duplicating. The

ReflexMax1 duplicator will automatically analyze

the master disc (this may take a few moments), and

begin duplicating at the maximum recording

speed.

7 The LCD will display the writing process as it

happens. The screen will display OK: when the

duplication is complete.

Note: When the duplication process is completed, the

writer drive will automatically eject the CD-R that has

been duplicated successfully. If the duplication process

failed, the CD-R will remain in the drive until the eject

button on the drive is pressed. For more information on

why a CD-R may not copy, please refer to the User's

Guide on the attached CD.

ACTIVATING USB CONNECTIVITY

IN ORDER TO USE OUR REFLEXMAX1 DUPLICATOR

AS AN EXTERNAL RECORDER, YOU NEED TO SET IT

TO OPERATE IN USB MODE.

1 Make sure the Reflex and your computer are

both turned off.

2 Locate the small switch next to the USB slot

on the back of the ReflexMax1. Before you con-

nect the USB cable, move the switch to the right

(toward the USB port).

3 Connect the USB cable to the port on the back

www.discmakers.com

v1.1

of the ReflexMax1. Then connect the other end of

the cable to an USB 2.0 slot on your computer.

4 Power on your computer and the Reflex by

pressing the round button in the lower right-hand

corner. The Reflex will perform a self-test. When

the self-test is complete, the image below will

appear on the LCD screen:

1. Copy

5 The Windows system message Found New

Device may appear during the first time you set up

the ReflexMax1 to your computer.

6 The Reflex will appear as a USB Mass Storage

Device, or USB 2.0 Device. Follow your comput-

er's on-screen instructions to set up a USB device.

7 In Windows Explorer and My Computer, the

bottom writer drive on the ReflexMax1 will appear

as a Compact Disc Drive icon with a new drive let-

ter, such as E:\. The drive is now ready to read and

write using the provided software or other author-

ing software. (Please refer to the software's help

section instructions.)

Note: To use the ReflexMax1 as a standalone duplicator

without the USB to PC connection, the switch located

next to the USB port must be pushed back to the left

(away from the USB port). If the switch is in the USB con-

nection position, the Reflex's controller will not recognize

the writer drive. If this happens, turn off the Reflex unit

and move the switch to the left. Then turn the Reflex unit

back on for normal operations. It's important to only

move the USB switch when the Reflex is turned off.

1-888-800-4041