ARO FA104A Instrukcja obsługi - Strona 5
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Wiertarka ARO FA104A. ARO FA104A 16 stron. Air feed peck drill
Drukuj stronę_ Assemble end plate (47) to rotor, aligning hole in end plate
with roll pin in cylinder. NOTE: Press on inner race of bearing.
_ Assemble nut (38) to end plate (41) and torque to 9 -- 12 ft lbs.
Be sure rotor turns without binding.
AUXILIARY GEARING
_ Pack bearings and lubricate gears liberally with ARO 33153
grease upon assembly.
_ Assemble one gear, with two bearings (52), to spindle, secur-
ing with shaft (51).
_ Assemble sun gear, where applicable, and opposite gear to
spindle, securing with shaft (51).
_ Rotate open portion of snap ring 90_ from either shaft.
_ Assemble bearings (50) to spindle, pressing on inner race of
bearings.
_ Gearing assembly should contain approximately 1/4 oz. (7 g)
of grease.
_ Assemble spindle and components into ring gear (57).
DRIVE GEARING
_ Pack bearings and lubricate gears liberally with ARO 33153
grease upon assembly.
_ Assemble one gear, with two bearings (52), to spindle, secur-
ing with shaft (51).
_ Assemble sun gear, where applicable, and opposite gear to
spindle, securing with shaft.
_ Rotate open portion of snap ring 90_ from either shaft.
_ Gearing assembly should contain approximately 1/4 oz. (7 g)
of grease.
_ Assemble one bearing (65) into ring gear (64), pressing on
outer race of bearing. NOTE: Assemble bearing with shielded
side toward gears.
_ Assemble spindle and components into ring gear.
_ Assemble paired spacers (66) and bearing (65) into ring gear.
_ Assemble auxiliary gearing to drive gearing.
_ Assemble spacer (49) and motor assembly to auxiliary gear-
ing.
_ Thread adapter (79) into spindle and slide motor and gearing
into housing (7), aligning key groove in ring gear (64) with slot
in housing. Remove adapter (79).
_ Lubricate ''O'' rings (2) and wiper (3) and assemble into hous-
ing (1).
_ Assemble housing (7) into housing (1) from the rear.
_ Assemble key (75) into slot in housing (7), long leg of key up-
ward. NOTE: Short leg of key to be flush with o.d. of housing
(7).
_ Assemble seal (76) to lock nut (77) and assemble lock nut to
housing (7) -- LEFT HAND THREAD. Do not tighten lock nut
(77).
_ Assemble torque arm (73) to housing (7), aligning slot with
key (75).
_ Push housing (7) toward the rear of the tool.
_ Assemble cap screw (34) to control rod (37), but do not tight-
en.
_ Orient cylinder (6) and components with housing (1), aligning
feed tube (98) with hole in housing.
_ Push piston (11) all the way forward in cylinder (6) and secure
piston to housing (7) using cap screw (13). Do not tighten cap
screw (13).
_ Push housing (7) and piston (11) toward the back of the tool
while sliding cylinder (6) into position.
_ Align components, then tighten cap screw (13).
_ Pull control rod (37) back and assemble adjustment screw
(20) into position.
_ Assemble adjustment screw (21) to bracket (28) and as-
semble gasket (16) and end cap (17) to cylinder (6), securing
adjustment screws.
_ Secure end cap with four cap screws (18). Do not tighten.
_ Tighten lock nut (77) securely -- LEFT HAND THREAD.
NOTE: If lock nut is not tight enough, motor and gearing could
spin in housing, due to high torque.
DISASSEMBLY/ASSEMBLY INSTRUCTIONS
_ Assemble nut (78) to lock nut (77) -- LEFT HAND THREAD.
_ Assemble adapter (79) to gearing spindle.
_ Align bracket (35) with adjustment screws (20 and 21).
NOTE: Adjustment screw (20) is to be free in hole in bracket
(35) and collar (23) on adjustment screw (21) is to clear brack-
et (35).
_ Tighten cap screws (18 and 34).
_ Assemble nose housing (84) to housing (1), securing with
cap screws (4).
_ Assemble cover (80) and end cap (81) to tool, securing with
screw (83).
_ Assemble cover (33) to tool, securing with screws (30).
PISTON AND HYDRAULIC CHECK DISASSEMBLY
_ Clamp tool in a smooth face vise, clamping on square portion
of handle (140).
_ Remove screw (83), releasing cover (80) and end cap (81).
_ Loosen screws (30), releasing cover (33).
_ Loosen four cap screws (4). Twist nose housing (84) clock-
wise and remove from tool.
_ Remove four cap screws (18), releasing end cap (17) and
gasket (16). Remove adjustment screws (20 and 21).
_ Remove cap screw (34) at front end of tool and pull control rod
(37) and bracket (35) from housing (1).
_ Remove cap screw (13).
_ Remove cylinder (6), including piston (11), feed tube (98) and
components. NOTE: Do not remove ''O'' rings (96) unless
damage is evident.
_ Remove piston (11) from the rear end of cylinder (6).
_ Remove retaining ring (101), releasing feed tube (98) from
piston (11). NOTE: Do not remove set screw (97).
_ Remove two screws (29), releasing bracket (28).
_ Unthread and remove swivel fitting (124)(toward front of tool)
and tube (126) from housing.
_ Loosen cap screw (27).
_ Unthread and remove swivel fitting (124) from control assem-
bly (127).
_ Loosen set screws in control assembly (127) and remove
control assembly from hydraulic check (129).
_ Remove retaining ring (128), releasing hydraulic check (129).
_ Remove cap screw (95), releasing spring (93) and spool (92).
NOTE: Do not remove valve sleeve (90) unless damage is ev-
ident.
_ Remove retaining rings (143), releasing screens (142) and
muffler pads (141).
_ NOTE: Do not remove logic assembly (135) or valve assem-
bly (137).
PISTON AND HYDRAULIC CHECK ASSEMBLY
_ Lubricate ''O'' ring (138) and assemble ''O'' ring and handle
(140) to housing, securing with cap screws (139).
_ Assemble muffler pads (141) and screens (142) into handle,
securing with retaining ring (143).
_ Lubricate ''O'' rings (89) and assemble to grooves in valve
sleeve (90).
_ Assemble valve sleeve (90) into housing (1).
_ Lubricate ''O'' rings (91) and assemble to grooves in spool
(92).
_ Assemble spool (92) and spring (93) into valve sleeve (90).
_ Lubricate ''O'' ring (94) and assemble to cap screw (95).
_ Assemble cap screw (95) to housing (1), securing spool and
spring.
_ Assemble bracket (35) to control rod (37), securing with cap
screw (34).
_ Assemble control rod (37) into housing (1).
_ Push housing (7) toward the rear of the tool.
_ Assemble cap screw (34) to control rod (37), but do not tight-
en.
_ Lubricate ''O'' ring (15) and assemble backup rings (14) and
''O'' ring (15) to groove in piston (11). NOTE: ''O'' ring to be lo-
cated between backup rings.
M103
85
5