DiscreteHeat TherMiser TME 3E Instrukcja obsługi - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Termostat DiscreteHeat TherMiser TME 3E. DiscreteHeat TherMiser TME 3E 4 stron. Programmable touch screen thermostat

Drukuj stronę

TherMiser TME operation

To ensure you follow the instructions correctly, please refer to the diagram below to familiarise yourself

with the layout and meaning of each of the on-screen icons.

1. Time and time interval setting

1.1 SETTInG THE TIME (FACToRy DEFAULT (00:00)

Press the time key

to scroll between hour/minute/day

of the week.

In each mode press the

(24hr) & day (1-7). Note: Mon = 1, Sun = 7.

The time and day will now be set.

1.2 TIME InTERVAL AnD TEMERATURE AUTo ConTRoL SETTInGS

Press and hold

for 5 seconds; screen displays 'loop'

(programming mode) then:

A. press

screen displays "12345"

(up) Once Screen displays "123456"

(up) twice Screen displays "1234567"

NOTE: In any of the above modes press

interval setting and target temperature; see 1.3.

1.3 SETTInG THE on/oFF TIME AnD TEMPERATURE

Press

again to enter the 1st time period/temperature setting

(Good morning)

factory default is (06:30 and 22°C).

Press

again and the ON time hour starts flashing

(default: 06:30), press

Press

again and the ON time minute starts flashing

(default: 06:30), press

Press

again and the target temp starts flashing

(default: 22°C), press

Press

again to enter into the 2nd time period/temperature

setting (leave for school/work)

to set, or

Press

again to enter into

setting and repeat as above.

Repeat through all of the remaining periods.

These are advanced settings and should be adjusted with caution.

to adjust the time

to select the time

to adjust the hour.

to adjust the min.

to set target temp.

repeat the steps above

3rd time period/temperature

2. Advanced settings

2.1 EnTERInG InTo ADVAnCED SETTInGS MEnU*

Press

so that the screen is off

Then press and hold

together. The unit enters the

menu at Status 1: "SEN" and in Function 00 (flashing).

To adjust the settings press

To move through menu Items 1-7 press the

See the menu below

Icon

FuncTIon

SEN

Controls sensor inputs

Upper limit

of external/

OSV

ThermaSkirt sensing

temp,

Differential

hysteresis between

DIF

off and on again of

external temp.

Room temperature

SFH

upper limit

Room temperature

SVL

lower limit

Calibrates tem of unit to

ADJ

the room, compensating

for external factors.

FRE

Frost protection

PON

Power on memory

FAC

Factory reset

2.2 LoCK SCREEn/MEnU

To prevent tampering and adjustment of the TherMiser unit, unit, press

seconds

appears. To unlock, press

2.3 LoCK SCREEn/MEnU

Manual Override

. Press

and

if heat required. Automatically resets to program mode at next time interval.

button.

oPTIonS

00: Built-in temp sensor only

01: External temp sensor only

02: Built in temp and External

Skirting Temp Sensor

Note: If no external sensor fitted,

"ERR" message displays, unit will

not function

5~99°C

1~9°C

5~99°C

-5~+5°

00: Frost protection OFF

01: Frost protection ON. 5°C

00: Auto memory, no power

01: NO power = no memory

Adjust using

until"00"

then press

to restore

factory settings

for 5 seconds

flashes then disappears.

to override current target temp.

FAcToRY

SeTTInG

42°C

2°C

35°C

5°C

0°C

for 5

appears