CAMDEN CX-WC17VR-PS Series Instrukcja instalacji

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Przez blokady CAMDEN CX-WC17VR-PS Series. CAMDEN CX-WC17VR-PS Series 6 stron. Restroom kit

Drukuj stronę

Electrified Locks, Relays and Timers

CX-WC17VR-PS SERIES RESTROOM KIT

INSTALLATION INSTRUCTIONS

1. GENERAL DESCRIPTION

The all-new Camden CX-WC17VR-PS Restroom Control Kit now comes with

the CM-221 Hands-Free Switch, which uses active infrared microburst sensor

technology and is designed to be used in ADA-compliant automatic door control

applications and access control. The CM-221 switch eliminates the spread of

germs by avoiding physical contact and provides greater convenience when

moving through the premises. For smooth operation, the CM-221 has an

adjustable time delay of 0.5 to 20 seconds and an adjustable range of 2" to 8"

(5cm to 20cm).

The CX-WC17VR-PS Restroom Control Kit is controlled by Camden's advanced

relay logic controller, the CX-33. Camden's CX-33 is a 'state of the art' logic relay

designed to support virtually any automatic door application.

The designation "PS" in the part number reflects that this kit now comes pre-

wired in a metal enclosure with a power supply that is ready to accept all field

wiring.

Operation at a Glance

The CX-WC17VR-PS has two modes: Mode 7 and Mode 8. The first mode refers

to the "Normally Unlocked" condition, when the exterior PUSH to OPEN column

switch is pressed or waved, it triggers the door operator to open the door.

However, the second mode refers to the "Normally Locked" condition, when the

exterior PUSH to OPEN column switch is pressed or waved, it first unlocks the

strike and triggers the door operator to open the door.

Inside the restroom, if the PUSH to LOCK column switch is pressed or waved, it

keeps the door locked in either mode and disables the exterior PUSH to OPEN

column switch. The LED light ring on the column switches turns red, indicating

the restroom is occupied. The user can either press or wave PUSH to UNLOCK

column switch as they exit the restroom. The LED light ring on the column

switches turns green, indicating the restroom is now available to be used.

Note: While exiting, the user can also use a crash bar, paddle, or doorknob

to unlock the door; in this case, the system will reset to its initial condition (mode

7 or mode 8), and the red light will turn green, allowing other users to use the

restroom.

Page 1 of 9

2. MODE SETTING

Mode Selection

Mode selection depends on the user requirements;

• If the user wants restroom to be unlocked during idle state, use Mode 7.

• If the user wants restroom to be locked during idle state, use Mode 8.

Note: The default mode for the CX-WC17PS is Mode 7

(normally

unlocked).

There are three LED displays that will allow you to see what mode you

have selected when advancing through the modes. To change the mode of the

CX-WC17PS, simply press the MENU button once and use the UP button to

advance to the desired mode.

Mode Editing

Camden builds in typical times for lock release and door operator activation

is ready to use without changing any parameters. If you need to change the

timing or delay for an output, it can be done by pressing the "MENU" button

within the mode you selected. Once the option is selected, you can use the

"UP or DOWN" buttons to select the timing needed. The first option (H & 1

flashing) will be how long relay 1 will be activated for (0-50 seconds). The

second option (d & 1 flashing) will be how long to wait before activating relay

2 (0-15 seconds). The third option (H & 2 flashing) will be how long relay 2

will be activated for (0-50 seconds). The fourth option (d & 2 flashing) will be

how long to wait before activating relay 3 (0-15 seconds). The fifth option (H

& 3 flashing) will be how long relay 3 will be activated for (0-50 seconds). See

the table 2.1

Factory Reset (Defaulting the CX-33)

To return the CX-33 back to its factory default settings, you will need to

remove the power, then hold down the "MENU" button while powering

up the CX-33. Once started, you will see the firmware version listed then a

number "1" will be displayed. Reconnect your power and press the "MENU"

button once, then use the "UP" or "DOWN" button to advance to the desired

mode.

For proper functionality, fully test the operation of the CX-WC11PS.

Table 2.1 Different Modes for WC17VR-PS

Display (M)

Description ( Mode you are in)

H, then 1

Relay 1 Hold Time

d, then 1

Relay 2 Delay Time

H, then 1

Relay 2 Hold Time

d, then 1

Relay 3 Delay Time

H, then 1

Relay 3 Hold Time

Sets the display ON or OFF during operating mode

Input delay on Activate. If other than 0.0 is selected, the input must

be held in for the time period chosen before the CX-33 will activate.

Set Dry Input 1 to activate on normally open or normally closed contact.

Set Dry Input 2 to activate on normally open or normally closed contact.

Set Dry Input 3 to activate on normally open or normally closed contact.

Set Dry Input 4 to activate on normally open or normally closed contact.

Set Dry Input 5 to activate on normally open or normally closed contact.

3. CM-7536VR COLUMN SWITCH INSTALLATION

Code Requirements: If installed according to these instructions the CM-7536VR Column switch will meet the requirements of the California Building Code (Section

1117B.6, Date: 2009), and Section 3.8.3.3.17(b) of the Ontario Building Code.

Installation Steps:

1. Take out pre-assembled unit from the box. To mount the switch, it

is required to disassemble a few components. Firstly, remove two

Phillips screw holding the top End Cap in place. Once both screws are

removed, take out the cap. Then, carefully pull out actuation bar and

place it aside so as to protect it from any surface damage.

End Cap

Actuation Bar

Figure 3.1 End Cap and Actuation Bar removal

2. Determine/Mark the optimum height and mounting location from the

finished floor to mount the column switch. See the illustration below

for the dimensions of the column switch.

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

CAMDEN DOOR CONTROLS. ANY

REPRODUCTION IN PART OR AS A

WHOLE WITHOUT THE WRITTEN

PERMISSION OF CAMDEN DOOR

CONTROLS IS PROHIBITED.

NEXT ASSY

CX-WC17VR-PS SERIES RESTROOM KIT

INSTALLATION INSTRUCTIONS

Parameters ( 1-15 )

0.0 to 50 seconds

0.0 to 15 seconds

0.0 to 50 seconds

Depends on Mode

0.0 to 50 seconds

ON or OFF

0.0 to 10 seconds

N/O OR N/C

6''

[151.13mm]

1 3 4 ''

[44.28mm]

3 3 8 ''

[85.17mm]

35 3 4 ''

[909.32mm]

37 5 8 ''

[955.04mm]

[609.60mm]

24''

Figure 3.2 Dimensions

3. Center the touchless switch over the box for wire connection, while

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

lining up the top edge with your mark (If installing through an in-wall

CAMDEN DOOR CONTROLS. ANY

REPRODUCTION IN PART OR AS A

WHOLE WITHOUT THE WRITTEN

electrical box), drill a Ø 0.25" hole for wire connection (If installing

PERMISSION OF CAMDEN DOOR

5502 Timberlea Blvd.

CONTROLS IS PROHIBITED.

Mississauga, ON Canada

L4W 2T7

Tel: (905) 366-3377

without an in-wall electrical box).

www.camdencontrols.com

TITLE:

UNLESS OTHERWISE SPECIFIED:

NAME

DATE

DIMENSIONS ARE IN INCHES

DRAWN

TOLERANCES:

CHECKED

FRACTIONAL

± 1/64

ANGULAR: MACH

±0.5 BEND

ENG APPR.

TWO PLACE DECIMAL

± 0.010

THREE PLACE DECIMAL

± 0.005

MFG APPR.

SIZE

DWG. NO.

REV

MATERIAL

Q.A.

COMMENTS:

USED ON

SCALE: 1:1

SHEET 1 OF 1

APPLICATION

DO NOT SCALE DRAWING

20 1 2 ''

[520.70mm]

Angelo R.

01/12/23

Page 2 of 9