Acoustic Energy AEGO5 plus Instrukcja obsługi - Strona 7

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla System głośników Acoustic Energy AEGO5 plus. Acoustic Energy AEGO5 plus 8 stron. Powered 5.1 surround sound speaker system

Drukuj stronę

1. Connecting Aego5 (with External Power Amplifier)

AEGOp5 Operation

- Delay Calibration

Centre

Subwoofer

Front

Right

Left

Rear Left

Rear Right

The recommended listening position is described below:

Centre channel speaker should be placed the same distance as the

left and right speakers from your listening position.

Rear left and right speakers should be placed behind your listening

position and above ear level.

If speaker placement is restricted due to the physical environment

of the room, delay calibration is sometimes necessary to achieve

the ideal listening environment.

If the centre speaker can only be placed nearer to you than the left

and right speakers, sound from the centre speaker will arrive

before the sound from the left and right speakers. The difference in

arrival time could may affect the sound quality and effect. Your

AEGO

5 allows you to adjust the speaker time delay to compensate

for this problem by increasing the delay time for the centre channel.

Thus sound from the centre, left and right speakers will reach you

at the same time. If your centre speaker is closer to your listening

position than the left and right speakers, press DELAY button

repeatedly until the centre channel is selected. To increase or

decrease the delay time, press D TIME + or D TIME - until the

desired delay is selected. The same procedure can be applied to

adjust the delay time of rear surround speakers if necessary.

AEGOp5 Operation - Time Delay

Adjustment on Centre Channel

Speaker

Delay Calibration

mute

test

Press the DELAY button and repeat to

balance

delay

prologic

select the length of delay time for the

field

EQ on/off

EQ setup

Rear Left (SL), Rear Right (SR) and

Centre(C) channels.

preset 1

preset 2

preset 3

save1

preset 4

load

The delay range for SL/SR is 0 to 15

BassManager

Cen

ms and 0 to 5 ms for centre.

SL/SR

VOL

D Time

Adjust the delay time for the selected

DRC

channel by pressing D TIME + or D

reset

TIME - on the remote control.

Press the DELAY Button will display the current

delay time for channel LS.

DOLBY DIGITAL CO

DELAY

SL 5 MS

Press the DELAY Button again will circle to next channel.

DOLBY DIGITAL CO

DELAY

SR 5 MS

Press the D TIME + or D TIME - button will increase or

decrease the delay time for current channel.

DOLBY DIGITAL CO

DELAY

SR 6 MS

AEGOp5 Operation - Time Delay

Adjustment on Surround

Speakers

Delay Calibration

mute

Press DELAY Button and repeat to

balance

delay

select the length of delay time for

field

EQ on/off

SL/SR/C channels.

preset 1

preset 2

The delay range for SL/SR is 0 to 15 ms

save1

preset 4

and 0 to 5 ms for centre.

BassManager

Adjust the delay time on selected

SL/SR

channel by pressing D TIME + or

DRC

D TIME - on the remote control.

reset

Surround Speaker Delay

Delay calibration for the rear surround

speakers may be necessary if the surround speakers are placed quite

close to your listening position. To correct the delay this may cause,

press the DELAY button repeatedly until SL or SR appear on the

display. Increase the time delay of the surround speakers by pressing

D TIME + until you are able to hear a 3D sound effect coming from

surround speakers.

Press DELAY Button again to move to the next channel.

DOLBY DIGITAL CO

DELAY

SL 5 MS

DOLBY DIGITAL CO

DELAY

SR 5 MS

Press D TIME + or D TIME - to increase or decrease

the delay time for the selected channel.

DOLBY DIGITAL CO

DELAY

SR 6 MS

AEGOp5 Operation

- Pro Logic Mode

Pro Logic Mode

Your AEGO

5 will automatically switch to

Pro Logic mode when it detects a Pro Logic

signal. With other types of input signal, you

can select the Dolby Pro Logic mode

manually by pressing Pro Logic button on

the remote. Repeatedly pressing the

Pro Logic Button will switch the Pro Logic

mode in between the following modes;

AUTO, ALL PCM, ENABLE and DISABLE.

If a Pro Logic signal is detected, AEGO

mode automatically, and the display shows the following information:

DOLBY DIGITAL CO

PROLOGIC AUTO

test

If a stereo signal (either analog or digital) is detected, AEGO

prologic

switch to stereo mode automatically. You can then convert the stereo

mode to Pro Logic mode by pressing the Prologic button until you see

EQ setup

the following on the display:

preset 3

DOLBY DIGITAL CO

load

PROLOGIC ALL PCM

Cen

DOLBY DIGITAL CO

PROLOGIC ENABLE

VOL

D Time

If you want to convert Pro Logic or 2-channel Dolby Digital signal into

Stereo mode, you can press the Prologic button until you see the

following on the display:

DOLBY DIGITAL CO

PROLOGIC DISABLE

AEGOp5 Operation - Speaker

Mode with Bass Manager

Speaker Mode with Bass Manager

The six LEDs on front panel of your AEGO

represent the six discrete audio channels

(Left, Right, Centre, Rear Left, Rear Right

and Sub). If a particular channel is active,

the LED will light up in green. The LED will

be red if that particular channel carries

bass signal below 120Hz.

Speaker Mode

Pressing the CEN button, switches the

centre channel on and off. The LCD will

display the following:

DOLBY DIGITAL CO

SPK C

DOLBY DIGITAL CO

SPK C

OFF

AEGOp5 Operation

Pressing the SL or SR button, switches the surround

channels on and off. The LCD will display the following:

DOLBY DIGITAL CO

SPK SUR

input

power

DOLBY DIGITAL CO

SPK SUR

mute

test

balance

delay

prologic

Pressing the SW button, switches the subwoofer on and off.

field

EQ on/off

EQ setup

The LCD will display the following:

preset 1

preset 2

preset 3

DOLBY DIGITAL CO

save1

preset 4

load

SPK SW

BassManager

Cen

DOLBY DIGITAL CO

SL/SR

SPK SW

OFF

VOL

D Ti

Bass Manager

5 will switch to Pro Logic

Pressing the BASS MANAGER button enables you to select from

three different settings of Bass; Bass Config.1, Bass Config.2 and

Bass Config.3. These selections will feed the bass signal

below 120Hz to different speakers as described below.

5 will

Bass Config.1

With this setting, the bass signal below 120Hz will be sent to the

subwoofer; the LEDs on the front panel indicating SW will be red,

and the LCD will show the following:

DOLBY DIGITAL CO

BASS CONFIG.1

Bass Config.2

With this setting, the bass signal below 120Hz will be sent to front left

and right speakers and the subwoofer; the LEDs on the front panel

indicating L/R/SW will be red, and the LCD will show the following

information:

DOLBY DIGITAL CO

BASS CONFIG.2

Bass Config.3

With this setting, the bass signal below 120Hz will be sent to all the

speakers; the LEDs on the front panel indicating L/R/SL/SR/SW

channels will be red and the LCD will show the following information:

DOLBY DIGITAL CO

BASS CONFIG.3

field

EQ on/off EQ setup

Bass Config. Off

preset 1

preset 2

preset 3

With this setting, the bass signal below 120Hz will be sent to all

save1

preset 4

load

the speakers; the LEDs on front panel of AEGOP5 indicating

BassManager

Cen

L/R/C/SL/SR/SW channels will be red and the LCD will show the

SL/SR

following information:.

VOL

D Time

DOLBY DIGITAL CO

DRC

BASS CONFIG.OFF

reset

OFF