Altman Pegasus 6 Skrócona instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Latarnia Altman Pegasus 6. Altman Pegasus 6 2 stron.

Drukuj stronę
QUICK START GUIDE
OPERATION AND PROGRAMMING - DIMMING CURVE AND DMX TERMINATION
DIMMING CURVE:
Pegasus will replicate one of three programmed dimming curves replicating linear and incandescent dimming.
SETTING
601
602
603
SETTING DIM CURVE:
1. Wait for Display to go blank (decimal points may still be active depending upon termination and DMX presence.
2. Using the programming buttons set the desired DIMMING CURVE setting
3. Wait 2 seconds, the display will then will change the [ HUNDREDS ] digit to a [P],asking for confirmation of personality change.
4. Depress the [ ONES ] button to confirm personality change Pressing any other button reverts back to 60X series display so that
modification can be made.
5. Depress the [ONES] button a second time to return out of programming mode.
DMX TERMINATION:
Pegasus is supplied with a programmable DMX terminator built into the luminaire. In a DMX system it
is recommended that the luminare that is at the end of the DMX Daisey-chain is terminated using a 120 OHM
resistor.
SETTING
998
999
SETTING DMX TERMINATION:
1. Wait for Display to go blank (decimal points may still be active depending upon termination and DMX presence.
2. Using the programming buttons set the desired DMX TERMINATION setting
3. Wait 2 seconds, the display will then will change the [ HUNDREDS ] digit to a [P],asking for confirmation of personality change.
4. Depress the [ ONES ] button to confirm personality change Pressing any other button reverts back to 90X series display so that
modification can be made.
5. Depress the [ONES] button a second time to return out of programming mode.
ABSENCE OF DMX:
When connected to a DMX network, if there is a loss of signal the following settings will effect the behavior of the Pegaus
Luminaire upon signal loss. This mode can be programmed by entering a number greater than 900. There are four (4) different
options upon the loss of signal.
SETTING
901
902
903
904
NOTE: upon loss of valid DMX setting 904 will initiate an instant change in the light output from the DMX setting to FULL ON (100%)
When this is done, after 2 sec, the display will change the [ HUNDREDS ] digit to [P],
asking for confirmation of personality change. This is confirmed with a press of [ ONES ] button. Pressing any other button reverts
back to 90X series display so that modification can be made.
Once confirmation is made: Display blinks and shows new Absence of DMX setting (oFF, HLd, PrE, FuL) for 4 sec, then goes to current
mode display.
Locked State:
When in Locked State, Buttons will have no effect until they are unlocked. To Lock (or unlock) the buttons, do the following button
sequence:
Wait a few seconds until the display goes blank,
1.
press and hold the [ ONES ] button,
2.
press and hold the [ HUNDREDS ] button,
3.
release the [ ONES ] button,
4.
release the [ HUNDREDS ] button.
Display will blink and show Loc (or unL) for 4 sec and then go to current mode
display. [Default is unlocked]
DISPLAY [RDM]
P01 [0]
P02 [1]
P03 [2]
DISPLAY [RDM]
I---I [0]
----
[1]
DISPLAY [RDM]
oFF [00]
HLd [01]
PrE [02]
FuL [03]
DESCRIPTION
Linear
Incandescent Fade 1
Incandescent Fade 2 (fast Bottom)
DESCRIPTION
Termination ON
Termination OFF
DESCRIPTION
off (dimmed to 0%) [Default]
hold last look (retains last DMX level)
preset (Standalone Preset level
full on (100%)
HUNDREDS ONES
PEGASUS 6 & 8 FRESNELS
TENS