Akiyama MC Club Instrukcja obsługi - Strona 4

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Mikser muzyczny Akiyama MC Club. Akiyama MC Club 13 stron. 3u rack stereo mixer

Drukuj stronę

FUNCTIONS

Front Panel

USB

THE CHANNEL

1.-Input assign switches

of the following backpanel inputs will be audible:

- Phono (turntable MM cartridge)

- CD or Line (CD and Line inputs are same characteristics)

- USB

2.-Gain Control:

Allows the adjustment of the channel input

sensitivity regarding the different source levels. Each channel

has an optical check up by means of the LED bargraphs of the

level meter.

3.-Channel EQ:

Independent control is provided for the high

(13KHz), the mid (1KHz) and the low (70Hz) frequency band.

Please be aware, that any boosted frequency band will increase

the total level and decrease the level headroom.

4.-Channel level meter:

before channel fader. To set the channel at the right level, when

in play back, set the Gain in a way that all green Leds light and

the yellow and red only blink.

5.-Headphones assign switch (Cue):

can assign any of the input channels to be replayed on the

headphones. Please note that you can only hear the required

source if the input assign switch is switched to the respective

position and the source is in play mode.

By means of these controls, you determine

6.-Channel fader:

the part of the overall level, that a specific channel contributes.

Please be aware of the final output level to be adjusted by the

Master and Booth controls.

To be

in-field replaceable

replacement, switch off the unit and unscrew the 4 outer screws

of the panel and remove it; unscrew the 2 screws that hold the

fader and replace it. Plug in the connector and screw the new part

to the main body again.

THE MAIN MIC CHANNELAND TALKOVER (CH-5)

This originally Main Microphone intended channel can be turn

into a normal stereo channel by means of the input assign switch.

However it bears some typical Mic channel format.

7.-Microphone equalizer:

controls are available.

Microphone signal.

USB

: These switches allow to choose which

The meter display the channel level

With these switches you

, this part is front-detachable. For

Only High and Low level tone

This equalizer will act upon the

8.-Channel 5 Level:

Channel 5 Level is a rotary knob instead of a fader.

9.-Auto Talkover:

the mixer detects Microphone signal, automatically all other

signals except the Main microphone level will be decreased. The

sensibility of Talkover function is adjusted by the control (10).

10.- Auto Talkover level:

lowered when the Auto Talkover function is engaged. The higher

the sensibility the lower the music level when Auto Talkover is

ON.

11.-Cue:

It is an standard Cue function as seen on the remaining

channels.

12.-Main Mic connection

(balanced). Use a Jack TRS.

MASTERAND MONITOR SECTION

13.-Main LED bars:

stereo output level of Master output when Monitor Selector (14)

in Master mode. When Monitor Selector selector in Cue mode

the left bargraph will show Cue level and the right bargraph will

depict Master (PGM) level.

14.-Monitor Selector:

15.-Master level control & Balance:

from Booth an external amplifier (main amplifier). The signal's

stereo balance can be controlled by means of control Balance

Master (bal). This signal is displayed on the level meter.

16.-Booth level control:

secondary amplifier to sound you booth cabin or to sound a

second area.

17.-Stereo/Mono Output Mode:

signal, normally stereo, in mono.

18.-Headphones Level:

you may control the headphones volume. Please check your

headphones impedance for a minimum of 32 Ohms and be aware

of high-impedance headphones reducing the maximum output

power of this output, so that you should choose a headphone with

less than 200 Ohms of impedance.

Caution!

Set level carefully, output signal is powerful enough to

damage your ears. We recommend start setting from control

turned fully counter clockwise.

mc club

ON/OFF

USB I/O

POWER

SENSITIVITY

ON/OFF

differently from the other channels

When AUTO TALKOVER is selected and

It determines the amount of dB

- It is a symmetric connection

The level meter bargraphs shows the

See point 13.

Controls independently

Controls independently from Master a

We can transform output

With a stereo headphone connected,