Alton DW18903PR-6H Instrukcja obsługi - Strona 7

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Odkurzacz Alton DW18903PR-6H. Alton DW18903PR-6H 12 stron. 6gallon (23 l) portable wet/dry vacuum

Drukuj stronę
English
Description (Fig. A)
WARNING :
Never modify the power appliance or
any part of it. Damage or personal injury could result.
Handle
1
Power cord
2
Power switch
3
Vacuum head
4
Lid latches
5
Dust tank
6
Hose
7
Accessory box / Cord wrap
8
Clean connect
lter
TM
9
Vacuum port
10
Blower port
11
12
Disposable dust bag
Assembly and Adjustments (Fig. A–C)
WARNING: To reduce the risk of injury, turn
appliance off and disconnect appliance from
power source before installing and removing
accessories, before adjusting or changing
set-ups or when making repairs.
start-up can cause
injury.
WARNING:
The lters
place while vacuuming, except as described
under
Wet Pick Up Applications
When vacuuming ne dust, you may also use an
additional paper bag or eece bag to make
emptying the canister easier.
1. If optional paper or disposable dust bag
be used, install .
NOTE: Be careful not to tear the bag. Place bag
securely onto vacuum port
seal for maximum dust collection performance.
2. Place the vacuum head
secure it by closing the canister latches
3. Insert end of hose
into threaded vacuum port
7
and tighten the end of hose on to the tank.

OPERATION

Instructions for Use (Fig. A, D, E)
WARNING:
Always observe the safety instructions
and applicable regulations.
WARNING: To reduce the risk of injury,
turn appliance off and disconnect
appliance from power source before
installing and removing accessories,
before adjusting or changing set-ups or
when making repairs.
cause injury.
1. Plug the power cord into an appropriate outlet.
2. Turn the power switch
For remote control use, set the power switch to remote
control position " II " and turn the vacuum on by pressing
the "
" ON button on the remote control.
3. Your ALTON construction dust extractor is tted
with the ALTON connection system. The allows for
An accidental
must always be in
9
under Operation.
is to
12
to provide a tight
10
onto the canister and
4
.
5
An accidental start-up can
to the ON position " I ".
3
a fast, secure connection between the suction hose
and power tool. The connector
7
directly to ALTON compatible tools or through the
use of an adapter (available from your local ALTON
upplier). Refer to the Accessories section for detail
on available adapters.
NOTE:
If using an adapter ensure it is rmly attached
to the tool outlet before following the steps below.
OPERATING INSTRUCTIONS
Remove / Change Used Dust Collection
Bag (Fig. A)
WARNING:
Appropriate personal protective
equipment like dust mask and gloves should be used
while handling used dust bags.
1. Turn off vacuum and unplug cord from outlet.
2. Unlatch lid latches
3. Pull the disposable dust bag
port
.
10
4. Seal the disposable dust bag
removing it from the machine.
5. Dispose of disposable dust bag
container according to statutory provisions.
Wet Pick Up Applications (Fig. A, H)
The vacuum requires only a minimum of conversion when
going from dry to wet pick up. A clean cartridge lter may
used for vacuuming small amounts of liquids. For best
results when vacuuming large quantities of liquid, it is
recommended using the foam lter
foam leter over lter cage
WARNING:
If foam or liquid escapes from the
machine,switch off immediately.
WARNING:
Do not use the machine with this set
up for dust class L.
The ball oat
will block air to the motor when the
14
canister is full and the sound of the motor will change
at once.
When the motor has a high pitched sound and air/
water ow stops, empty the canister.
1. Turn off vacuum and unplug cord from outlet.
2. Unlatch lid latches
10
3. Empty contents of dust tank
container or drain.
CAUTION:
Clean the water level limiting device
regularly and examine it for signs of damage.
NOTICE:
DO NOT remove ball oat
will cause damage to the vacuum. The ball oat keeps
water from entering the motor.
Before using the vacuum for wet pick up:
• Ensure the canister is empty and free of excessive dust.
• Remove the lter
To Convert Back to Dry Vacuum
Operation (Fig. A)
1. Empty canister, refer to empty canister instructions.
2. Place canister upside down position until dry. DO
NOT use wet canister for dry pick up.
3. Place vacuum head
4. Reinstall lters when vacuum head is dry. See Filters
under Maintenance.
5. When canister is dry place the vacuum head
onto the canister and secure it by closing the
lid latches
.
5
5
connects
13
and remove vacuum head
5
carefully from vacuum
12
opening tightly when
12
in appropriate
12
and install the
22
and remove vacuumhead
5
into a suitable
6
, doing so
14
.
9
on a level surface until dry.
4
.
4
.
4