ClearStream 4MAX C4MVJ Skrócona instrukcja montażu/instalacji
Przeglądaj online lub pobierz pdf Skrócona instrukcja montażu/instalacji dla Antena TV ClearStream 4MAX C4MVJ. ClearStream 4MAX C4MVJ 2 stron.
Drukuj stronę
Connect the antenna to the TV or converter box and run a full channel scan. If reception is not as desired, move the antenna and rescan for the available channels.
1
Attach the Antenna
Elements
(1)
to the
Antenna Spine
(2)
by
placing the Short Tubes
(2)
in the spine holes, and
screwing in the 60mm
Antenna Spine Bolts (6).
6
INSTALLATION ON THE J- MOUNT MAST
Required: Coaxial Cable
(sold
separately), Adjustable Wrench, Power Drill, 3/16" Drill Bit,
8 and 10mm Ratcheting Drivers, and a #2 Phillips Screwdriver
Before permanently attaching the antenna to any surface, TEST RECEPTION
in that area.
HELPFUL TIP: IT'S IMPORTANT TO CHECK THE RECEPTION IN THE LOCATION
WHERE YOU INTEND TO INSTALL THE ANTENNA, PRIOR TO ATTACHING THE
J-MOUNT MAST TO ANY SURFACE.
11
10
11
To add the mounting
hardware, assemble
the hardware, as
shown, and use the
Mast Clamp Bolts
(9)
to secure.
9
Follow the instructions in the owner's manual of your TV or converter box to change the input from 'CABLE' to 'ANTENNA', 'AIR', or 'BROADCAST'.
Point the front of the antenna in the direction of your TV stations' broadcast towers and check reception by
scanning for channels. If you are not receiving all of the available channels, move the antenna and rescan.
J-MOUNT INSTALLATION
Attach the J-Mount Mast
(8)
to the Mount Base
the Hex Bolts and Nuts (12), as shown above.
Mark the Mount Base
(14)
position on the desired surface
and drill pilot holes, 1" deep, for each of the 50mm
J-Mount Bolts (13).
Place the Sealing Pads
(15)
over the pilot holes, and the
Mount Base
(14)
on top of the Sealing Pads.
Tighten the J-Mount Bolts
(13)
to secure the base to the
surface.
Call to Learn.
Toll-Free Helpline:
Quick Start Assembly/Installation Instructions
CLEARSTREAM 4MAX™
Before beginning assembly, make sure all parts needed are present.
Coaxial cable sold separately.
2
3
4
5
1
2
WALL MOUNT
(14)
with
1-877-825-5572
7
8
6
4
Next, add the VHF Dipoles
19mm End Cap Screws (4).
To locate the broadcast towers in your area, go to
antennapoint.com and enter your zip code, or scan the
QR code.
Before installing the antenna on the J-Mount Mast (8), adjust the mast,
so it is in a vertical position. You will need to adjust the antenna a er it
is mounted for the best reception.
Install the antenna on
the J-Mount Mast
(8)
by
positioning the Mast
Clamp
(10)
around the
mast. Tighten the Wing
Nuts
(11)
to secure the
antenna to the mast.
14
13
15
Technical Assistance is available
and Saturday – Sunday, 10:00 am to 6:00 pm, Central Time.
The ClearStream 4MAX™ comes with:
9
11
1)
2- Antenna Elements
10
2)
Antenna Spine with 2 Short Tubes
3)
2 - VHF Dipoles
4)
2 - 19mm Dipole End Cap Screws
12
13
5)
2 - Dipole End Caps
6)
2 - 60mm Antenna Spine Bolts
14
7)
Mast End Cap
8)
J-Mount Mast
9)
2 - 25mm Mast Clamp Bolts
15
10)
Mast Clamp and Back Plate
11)
Wing Nuts and U-Clamp
12)
2 - 40mm Hex Bolts and Nuts
13)
4 - 50mm J-Mount Bolts
14)
Mount Base
15)
4 - Sealing Pads
3
5
(3)
using the Dipole End Caps
FRONT VIEW ON MAST
Monday – Friday, 9:00 am to 9:00 pm
(5)
and the
7
8
14