EdilKamin LOGO Instrukcja instalacji, użytkowania i konserwacji - Strona 11
Przeglądaj online lub pobierz pdf Instrukcja instalacji, użytkowania i konserwacji dla Piec na drewno EdilKamin LOGO. EdilKamin LOGO 20 stron.
Drukuj stronę
/RDGLQJ WKH IHHG VFUHZ
Should the pellet hopper empt\ completel\ the feed screw
must be lled. 7o do so, keep the and ke\s pressed simul-
taneousl\ for a few seconds (on the remote control or s\noptic
panel). Once released, REF,LL will appear on the displa\.
7his must be carried out before ignition if the stove has stopped
due to the pellets having nished.
,t is quite normal for some pellet residue to remain inside the
hopper, this is what the feed screw is unable to pick up.
Once a month, full\ vacuum the hopper to prevent dust\ resi-
due from accumulating.
$XWRPDWLF LJQLWLRQ
With the stove on standb\, press the button for seconds
(on the s\noptic panel or remote control). 7his will startup
the ignition process, Start will appear on the displa\ and a
countdown will commence in seconds (). 7here is no
preset time for the ignition process its duration will be automa-
ticall\ shortened if the control board detects that certain tests
have been carried out positivel\. 7he ame appears after about
minutes.
0DQXDO LJQLWLRQ
$t a temperature lower than q& too low for the electrical
resistance to become red hot - or if the resistance is temporaril\
not working, \ou can use a relighter to ignite the stove.
,nsert a well-lit relighter into the combustion chamber, close
the door and press on the s\noptic panel or remote control.
2SHUDWLQJ PRGHV
0DQXDO the user sets the desired operating power (from
a minimum of to a ma[imum of )
$XWRPDWLF the user sets the temperature desired in the
room. 7he stove reads this and adMusts the power to reach
the set temperature. Once this is reached, it sets itself to
power .
0DQXDO PRGH IURP V\QRSWLF SDQHOUHPRWH FRQWURO
RSWLRQDO
With the stove in operation mode or on standb\, press and
release the 0E18 button on the s\noptic panelremote
control and 3ower will appear on the displa\ (showing
the power at which the stove is working). Rotate the left
knob or press the ke\ on the remote control to increase
the operating power (from 3ower to 3ower ).
Setting the fan via the S\noptic 3anel
With the stove in operation mode or on standb\, rotate the
right knob to adMust the ventilation setting (from to in
all powers).
$XWRPDWLF PRGH IURP V\QRSWLF SDQHOUHPRWH FRQWURO
RSWLRQDO
3ress the 0E18 button twice to switch from manual to
automatic mode and adMust the temperature desired for the
room (use the left knob on the panel or the and ke\s
on the remote control to set the temperature between
and 9 ...., and the stove will regulate the operating power
required to reach it.
,f the set temperature is lower than the room temperature,
the stove works at 3ower .
INSTRUCTIONS FOR USE
- 29
6KXWGRZQ
)RU JUHDWHU FRPIRUW WKH VWRYH DQG WKH DLU YHQWV JR RII
DW WKH VDPH SRZHU DW ZKLFK LW ZDV RSHUDWLQJ
With the stove in operation mode press the ke\ for
seconds (on the s\noptic panel or remote control). 7he
shutdown procedure will begin and the countdown is
displa\ed. 7his varies according to the power at which it
is running when the shutdown phase begins.
7he shutdown phase (which will e[tinguish the ame
without leaving an\ unburnt material in the combustion
chamber and cool the stove), consists of
3ellet loading ceases.
9entilation is activated at the level at which the stove
was operating.
Smoke e[pulsion motor enabled.
1HYHU XQSOXJ WKH VWRYH GXULQJ WKH VKXWGRZQ SURFHVV
6HWWLQJ WKH FORFN
3ress the 0E18 button for seconds and use the and
ke\s to follow the instructions given on the displa\ to
access the &lock menu. 7his allows \ou to set the time on the
electronic control board.
7hen press 0E18 and the following data appears in
sequence this can be adMusted
da\, month, \ear, hour, minutes, da\ of the week.
When Save" appears on the displa\ \ou can check that
the settings have been entered correctl\ before con rming.
3ress 0E18 to save the information ( Save OK then
appears on the displa\).
:HHNO\ WLPHU
3ress the 0E18 button on the remote control for
seconds to access the time setting function and press the
ke\ to access the weekl\ timer function
OFF will appear on the displa\.
$ ma[imum of three timer programs can be set for each
da\ of the week.
$s \ou con rm via the 0E18 button, one of the following
options will appear
- 1o 3rog. (no program is set).
- 'ail\ program (a single program is set for ever\ da\)
- Weekl\ program (a program is set for each da\ of the
week).
0ove from one to the other using the and ke\s.
8se the 0E18 button to con rm the 'ail\ program
option and access the selection of the number of programs
(ignitionshutdown) to be set per da\. 8se the 'ail\ program
option to set the identical programs for ever\ da\
of the week.
7he following will be displa\ed if the ke\ is pressed
- 1o 3rograms.
- st dail\ program (one ignition and one shutdown per
da\), nd dail\ program (same as before), rd dail\ program
(same as before).
8se the 0E18 button to show them in reverse order.
,f the st program is selected, the ignition time is shown.
7he displa\ shows ,gnition +our .; use the
ke\s to change the hour and press 0E18 to con rm.
7he displa\ shows ,gnition 0inutes .; use the
ke\s to change the minutes and press 0E18 to con rm.
-
3rogram O1