Artison ARCHT-6-SSTT Instrukcja instalacji - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Głośniki Artison ARCHT-6-SSTT. Artison ARCHT-6-SSTT 3 stron. For 6-1/2" & 8" singlepoint/in-ceiling/wall

Drukuj stronę

Artison models

ARCHT-6

6-1/2" in-ceiling / wall

ARCHT-6-SSTT 6-1/2" singlepoint in-ceiling / wall

ARCHT-8

8" in-ceiling / wall

ARCHT-8-SSTT 8" singlepoint in-ceiling / wall

Congratulations! You have purchased a high quality stereo loudspeaker. When

matched to comparable electronic equipment, expect years of quality high fidelity

sound. The Artison brand is based on the belief that music matters and we are

focused on delivering superlative music reproduction everywhere in your home.

The following manual is designed to give you, the installer or owner, basic

information as to the speaker's installation and operation. It is beyond

the scope of this manual to go into all the details that must be taken into

consideration in a sophisticated high fidelity system. When installing the

wiring and speakers it is important to adhere to all local codes and regulations.

Consulting a professional can help to maximize your system's performance.

If you have any questions regarding this speaker which are not answered by this

manual, contact your local dealer for assistance.

MINIMUM TOOLS REQUIRED

# 2 Phillips Head Screw Driver / Drill Driver

Wire Cutter / Stripper

Other Possible Tools

Tape Measure, Pencil, Ladder, Drywall Saw, Stud-Finder, etc.

GENERAL DESCRIPTION

These two-way speakers have specially designed woofers

with linear long throw butyl rubber surrounds for long life and

superior damping. Dome tweeters are utilized for excellent

high frequency dispersion throughout your entire listening

environment.

SHIPPING DAMAGE

Each speaker is thoroughly tested before it leaves the factory.

However, in shipment, accidents may occur. Please inspect your

speakers carefully when you receive them to make sure there

is no damage. If there is, please notify your dealer or supplier

immediately for assistance. If you received your speakers by

public transportation, report the damage immediately to the

shipping company.

AMPLIFIER OPERATION

These speakers will perform well with amplifiers from 5 to

125 Watts RMS. However, damage to the speakers can be

done by amplifiers of nearly any power rating if the amplifier is

overdriven into clipping. "Amplifier clipping" is a phrase used

to describe a condition when, because of the volume demand,

an amplifier is being asked for more power than it can give.

Clipping causes distortion of the audio signal. If you should hear

an unusual amount of distortion at high listening levels then

consider reducing the volume. DAMAGE DONE TO A SPEAKER BY

CLIPPING IS NOT COVERED UNDER THE WARRANTY.

Install Guide 009-1589-00

frameless w/ diffraction ring

diffraction ring

SPEAKER PLACEMENT

Placement of in-ceiling and in-wall speakers should be carefully

considered. Please contact a professional for assistance if you are

uncomfortable with the planning or installation process. Ideally,

the speakers should be located where they will provide the best

possible sound and ease of installation. It is beyond the scope of

this publication to discuss all of the various aspects of speaker

placement. However, here are a couple quick suggestions.

For the front channels of a home theater we recommend that the

speakers be placed between 18 and 36 inches (0.45m to 0.9m)

from an adjacent wall/surface, as measured to the center of the

hole. Avoid placing the speakers less than 12 inches (0.3m) from

an adjacent wall. When placing speakers near a corner, avoid

locating them an equal distance from the two adjacent surfaces.

If the drywall has not yet been installed, rough-in-kits are

available to reserve the speaker location. The hole is then cut

when the drywall is installed.

WIRING

To achieve maximum performance we recommend that the

speaker cable be at least 16 gauge or larger for runs over 50 feet

(15m) and that the cable be double insulated. A CL2 or CL3 rated

cable is usually sufficient. "Zip cord," which is single insulated

and is often made with clear insulation, should be avoided as it

is not as durable. Allow about 2½ feet (0.8m) of free cable at the

speaker cut-out and sufficient length at the other end to reach

the electronics. Having to add extra cable later can be tedious and

time consuming.

Avoid bundling speaker cables parallel to electrical cables for

extended lengths. Though the impedance is low and the likelihood

of interference low, this may help reduce hum and RF interference.

INSTALLATION GUIDE

For 6-1/2" & 8" In-Ceiling / Wall

Overall

Cut-Out (Round x

8-7/16" round

7-1/4" x 3-9/16"

8-7/16" round

7-1/4" x 3-5/16"

9-7/8" round

8-5/8" x 4"

9-7/8" round

8-5/8" x 3-7/8"

diffraction ring

frameless grille

removal notch

Depth)K-

ARCHT-6

page 1 of 2