CustomWorks Dominator Model - Strona 10

Przeglądaj online lub pobierz pdf Model dla Zmotoryzowany samochód zabawka CustomWorks Dominator. CustomWorks Dominator 17 stron. 1:10 scale 4wd dirt oval car kit

Drukuj stronę

Shock Bag

Bag J

-Parts for

Step#1

1425 Med / 1426 Short Qty 2ea

2 Med / 2 Short Shock Body

-Parts for

Step#2

1432

Qty4

Eyelet Cap

-Parts for

Step#3

1488

Qty4

1407

Spring

Spring Bucket

STEP #1

1429 MED

NOTE: Put a few

1430 SHORT

drops of oil on the

O-Rings!

1425 MED

1426 SHORT

1434

TIP: To press clip in easiest, compress the clip

so the diameter is a little smaller.Insert open

1250

end of clip first, working counter-clockwise to

1435

the bent end as shown.

SHOCK FILLING INSTRUCTIONS:

1) Holding the

2) Slowly move the

shaft up and down

shock upright,

fill with oil until

several times to allow

the top of the

air bubbles to escape

body.

to the top.

40 wt

suggested

starting point.

6) Then the shaft

7) If the shock does not push out

this far there is not enough oil in

should push itself

out to its full length

it. Add just a little oil and try

slowly.

steps 5-6 again.

Shock Assembly

1429 Med / 1430 Short Qty2ea

2 Med / 2 Short Shock Shaft

1431

Qty4

Threaded Cap

Qty4

1408

Qty4

1255

Qty4

Mount Ball

Spacer

BUILD 2 SHORT & 2 MED

5230

LENGTH SHOCKS!

- USE #1429 SHAFT WITH

1436

#1425 BODY.

- USE #1430 SHAFT WITH

#1426 BODY .

- Attach 1436 Shock Piston to

Shock Shaft using 5230 E-Clips

to secure.

- Press 1250 O-rings into the Shock

Body followed by 1434 Shaft

Guide. Retain using 1435 Clip.

3) Refill with

oil to the top

of the shock

body.

1434

Qty4

Shaft Guide

1437

Qty 4

1433

Firm Bladder (BLACK)

Spring Collar

5278

Qty 4

5274

1:1

4-40 x 1" SH Screw

4-40 x 1/2 SH Screw

STEP #2

- Snap Pivot Ball into the 5228 Ball End. Thread the

Ball End onto the Med Shock until the Ball End is

flush with the end of threads on the shaft. Do the

same with the 5235 Ball Cup to the Short Shock.

- Press 1432 Eyelet Cap into 1431 Threaded

Shock Cap so that guide in the Eyelet Cap lines

up in the recess in the Threaded Shock Cap.

- Press the 1437 Firm Bladder (BLACK) into the

Threaded Shock Cap so the dome of the

bladder points away from the Eyelet Cap.

- Thread 1433 Spring Collar onto the

Shock Body.

-NOTE: See shock filling tips for more

instructions.

4) Thread the Eyelet Cap

assembly onto the Shock

Body until it is hand

tight. Oil should seep

out of the bleed hole

in the Threaded Cap.

8) If the shockrebounds too fast , or you cannot push the shaft in

until the eyelet hits the body, there is too much oil. Loosen the cap

about 2 full turns and pump out a small amount of oil by pushing

the shaft in. Retighten the cap and try steps 5-6 again.

1250

Qty 8

1435

Qty 8

O- Ring

Reatining Clip

5228

Qty4

Short Ball End

1:1

Qty 2

5273

Qty 2

4-40 x 3/8 SH Screw

5) Move the shock shaft in and out a few

times and then push it all the way in. It

should be easy to push the shaft in until

the eyelet is within 1/8" of the

shock body.

1:1

1436

Qty4

5230 Qty 10

Piston

E-Clip

5228

Qty4

Pivot Ball

5217

Qty 4

5233

Qty 2

4-40 Lock Nut

4-40 Coned Washer

1431

1432

1437

1433

5228