ARTRED AR-55 Instrukcja obsługi - Strona 6
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Scrubber ARTRED AR-55. ARTRED AR-55 11 stron. Scrubber-dryer
Drukuj stronęMachine Installation
Installation and Connection of Squeegee Component
1. Stop and place the machine on the level ground and take out thekey.
2. Lower the lifting rod of the squeegee to the lower position.
3. Install the squeegee to the squeegee installation bracket as shown in the figure.
Ensure to fully place the fastening knob into the jack and then tighten the knob.
4. Connect the vacuum suction pipe to the squeegee component.
5. Examine the squeegee adhesive tape and reasonably adjust.
Installation of Brush/Scouring Pad
Explanation:
As for the brush and scouring pad suggested for use, please
refer to the section of [Information on Brush and Scouring Pad] in this Guide or
consult your local authorized dealer.
1. Stop and place the machine on the level ground and take out thekey.
2. Step on the brush head lifting pedal to lift up the brush head from the ground.
3. Place the scouring pad on the holder and then install the drive disc. Fasten the
central lock to fix the scouring pad.
4. Align the holder/brush installation stud at the motor drive disc buckle and
press the motor switch of the brush.
5. If the holder and brush are to be dismantled, step on the brush head lifting
pedal to lift up the brush head from the ground, press the motor switch of the
brush.
Machine Operation
For safety: Please do not operate this machine before reading and understanding
the operation manual.
Warning:
fire or explosion hazard. Do not operate the machine close to or in
the place where there is flammable liquid, air or dust.
Pre-operational Examination
□Clean the dust on the ground.
□ Check the scale of the battery coulomb meter. (refer to the
battery coulomb meter)
□Check the abrasion conditions of the scouring pad/brush.
□Check the abrasion conditions of the squeegee adhesive tape and reasonably
adjust the angle.
□Confirm that the waste water tank is blank and has been equipped with clean
floating filter screen.
□Check the abrasion conditions of the skirt section of the brush head.
Machine Operation
1. Switch the key of the main power supply to the position of (Ⅰ).
2. Pull down the squeegee lifting rod to lower the squeegee component to the
ground.
3. Step on the brush head lifting pedal to lower the brush head to theground.
4. Switch on the clean water control knob.
5. Press the motor switch of the brush and press the switch of water suction
motor.
6. Motor drive model: adjust the speed control knob to the cleaning speed
required by you.
Explanation: It is suggested to use the cleaning speed of 45-60 meters/min.
Machine Operation Duration
Warning:
fire or explosion hazard. Please do not pick up flammable materials
or reactive metals.
1. Each cleaning path overlaps by 5cm.
2. Let the machine advance constantly to avoid ground damage.
3. If there is drag mark on the ground after the squeegee absorbs water, remove
the waste with duster cloth wiping adhesive tape. Clean in advance to prevent
drag mark.
4. Do not operate the machine on the slope with a slope over 5% (3°).
5. If there is too much foam, it is suggested to pour the used defoaming
solution into the waste water tank.
Note:
Do not let the foam enter the filter screen so as to avoid damage to
vacuum motor. The foam will make the switch of the filter screeninvalid.
6. Use double cleaning method to clean the extremely dirty area. Lift up the
squeegee firstly for cleaning, sink with solution for 3-5 min, lower the squeegee
for re-cleaning.
7. Replace or rotate the scouring pad as required.
8. Observe the power consumption of the battery coulomb meter (refer to
the battery coulomb meter).
9. Observe the residual liquid amount through the liquid meter of the clean
water tank. In traditional scrubbing method, the consumption for each 10 min is
about 10l.
10. When the solution in the clean water tank is used up, empty the waste water
tank firstly, then re-pour the solution.
11. When the staff leaves the machine, stop and place the machine on the level
ground and take out the key.
12. After cleaning, carry out daily maintenance procedure.