DLX Luxe X Skrócona instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Sprzęt do paintballa DLX Luxe X. DLX Luxe X 2 stron.

SETUP & OPERATION

- After use, remove the hopper and paintballs,then turn off your Luxe

DEGASSING

turn off the ASA by swinging the ASA charging handle to its extended position. This will relieve air pressure between the ASA

and vertical regulator, but, the Luxe

Power Core will still be charged with air. Relieve the internal pressure by pressing the bot-

tom back of the quick-strip latch at the back of your marker. This will degas your Luxe

soda. Do not attempt to degas your Luxe

X while the ASA charging handle is in the charged position, as the continuous rush of

gas will unseat an o-ring in the Luxe

X quick-strip system causing a leak.

WARNING! – If the Luxe

Power Core is pulled out of the body before it is fully de-gassed it may be under enough pressure to

fire a single low-power shot as it is being removed. Always turn off and or remove the gas supply (see the Luxe

start) and hold the quick-strip latch open until no escaping gas can be heard, before pulling back to extract the power core.

DEGASSING

IMPORTANT!

Degas ASA

by rotating lever

- The Luxe

power core can be removed for cleaning or inspection by gripping the top of the quick-strip latch and

CLEANING

pulling the entire assembly out the back of the marker. The bolt serves as the marker's exhaust valve and is the main moving

part. Unscrew the fire chamber from the quick-strip mechanism and the bolt may be removed from between the two compo-

nents. Clean the parts of the power core and replace any o-rings showing signs of damage or severe wear. Lightly lubricate the

contact surfaces of all o-rings with Luxe

GR33SE

not use oil. This simple cleaning, and the Detent/Vision

properly care for your Luxe

ELECTRONIC ADJUSTMENTS

PROGRAMMING

– The The Luxe

X OLED display and exclusive Luxe

ware menus. Unlock the marker and turn it on while holding back the trigger to open the Main Menu. Pull the trigger to scroll through the

available settings. To make a change, find the desired setting and tap the power button. The Luxe

for that sub-menu on its OLED display with "SET" appearing on screen. Changes may be made by pulling the trigger to cycle through the

available values. Tapping the power button will select a value and return to the main menu. Press the power button for approximately 2

seconds to turn off the Luxe

and exit programming mode.

X, secure the barrel blocker in place and

X and sound similar to opening a can of

LIFT UP

PUSH IN with thumb

Degas by lifting Tail Cover

until fully degassed.

. Non-approved lubricants may cause damage and void your warranty. Do

cleaning mentioned below is the only routine maintenance required to

voice feedback make it easy to navigate your marker's soft-

will display the currently selected value

– Turn on your Luxe

POWER

pressing and holding it for two seconds. When the Luxe

display will be illuminated to show its status.

ing off your Luxe

X is the equivalent of setting the safety on a mechanical

paintball marker, but should not be relied on in place of a barrel blocking

device and paintball goggles.

idle for one hour.

– The Vision

VISION

X manual or quick-

off or back on with a quick double-tap of the button. Vision

{FIG. 06}

indicated in the Luxe

tected in the breech, or an empty circle when the Vision

Vision

Fault indicates that the beam has not cleared after firing, usually due

to debris blocking an eye.

TOURNAMENT LOCK

he programming menu unavailable when it is turned on. To change the lock

setting, open the left side of the rubber grip and slide the tournament lock

switch (located next to the USB-C charging port) towards the barrel to un-

lock, or towards the back of the marker to lock. The lock status is displayed

on the OLED screen with an open or locked padlock. Some events may

require the rubber grip to be secured with screws in place of snap posts, so

that the lock may not be accessed without using a tool.

BARREL/REGULATOR GRIP PANEL

XL Barrel and install it on your Luxe

vertical regulator can be changed by removing the regulator nut on the

bottom of the vertical regulator with a 5/16-inch hex-key.

BARREL BLOCKER

and should be used any time the Luxe

turned on unless all persons within range are protected by paintball goggles

and or netting. Slide the barrel blocker over the end of the barrel cinch

down the cords over the rear of the marker to secure it in place.

AIR SETUP

- Your Luxe

sure spikes from liquid CO

Luxe

warranty. Use only regulated compressed air as a power source. HPA

systems set for 450-550 psi output are ideal. Low-output 250psi systems

may be used with your Luxe

rates of fire. With the barrel blocker in place, screw a filled paintball

compressed air system into the Luxe

air by rotating the ASA charging handle to the rear position.

WARNING! – Once your Luxe

enough air to fire 2 or more shots, even after the HPA system has been

removed.

VELOCITY ADJUSTMENT

the start of each paintball session. Attach a hopper and filled HPA system to

your Luxe

X. Fill the hopper with fresh 68-caliber paintballs. While wearing

paintball goggles, while everyone in range is similarly protected, remove the

barrel blocking device, rotate the ASA charging handle to charge your Luxe

X with air, turn on the power and take a few test shots over a chronograph.

Adjust the velocity of your Luxe

the bottom of the marker's vertical regulator. Turn clockwise (like tighten-

ing a screw) to increase velocity and counter-clockwise (like loosening) to

decrease. After each adjustment take a few shots, then re-adjust as needed

until the desired velocity is reached. Never adjust your Luxe

velocities greater than 300 feet per second (91.4 m/s).

SETUP & OPERATION

X by double-clicking the power button or

is on, the Luxe

{FIG. 03}

WARNING! – Turn-

Your Luxe

X will turn off automatically if it sits

anti-chop system is on by default. It may be turned

status will be

X display with a solid circle when a paintball is de-

beam is unbroken.

– The Luxe

X tournament lock switch makes t

- Assemble the Included Freak

X. The interchangeable grip panel on the

- The barrel blocker is an important safety device

X is connected to an air supply or

X is a high-performance paintball marker. Pres-

can cause internal damage and will void the

X but may cause velocity drop-off at high

ASA. Charge your Luxe

X with

{FIG.04}

X has been charged with air, it can hold

- Velocity must be tested and adjusted at

X with a 5/32-inch hex key inserted in

X to fire at

{FIG. 05}

POWER

FIG. 2

Programming

Lock

Mode &

BPS cap

Vision™

Status

Software

Version

Max ROF

Battery

Level

Power

FIG. 2

AIR SETUP

AIR OFF

AIR ON

VELOCITY ADJUSTMENT

–