Ashdown Fallen Angel 60 DSP Combo & Head Instrukcja obsługi - Strona 10
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Wzmacniacz do instrumentów muzycznych Ashdown Fallen Angel 60 DSP Combo & Head. Ashdown Fallen Angel 60 DSP Combo & Head 12 stron.
Drukuj stronę
#16598 - Manual 2005_FA
18/4/05
FUSED MAINS INLET SOCKET - This is for
connection to the mains supply using
supplied cable. Always use a mains outlet
that has an earth/ground connection for
safety. Never remove or replace the plug on
the supplied cable. Always replace the fuse
with the same type and rating as stipulated
on the rear panel adjacent to the mains inlet
socket.
FOOTSWITCH SOCKETS - There are 3
footswitch sockets provided on the amplifier.
For any of these footswitch sockets to
operate, it is essential that the corresponding
front panel push buttons are in the OUT
position. The first of these sockets is a mono
jack for connection of the supplied 4-way
footswitch. Always connect this prior to
turning on the power to the amplifier as
footswitch power is derived from the
amplifier. The next 2 footswitch sockets are
both stereo sockets and use a standard 2-
way, push on/push off type footswitches for
their operation. These may be used as an
alternative to the dedicated 4-way footswitch
supplied.
EFFECTS LOOPS (180 Head) - There are 2
Effects Loops provided on this amplifier. Each
has two jack sockets for Effects Send & Effects
Return signals; the Effects return socket also
has an Effects Return Level control associated
with it for adjusting the level of the returned
signal. There is a single push button for
dedicating these Effects Loops as either Serial
(where the signal path through the amplifier
is broken by the effects loop) or Parallel
(where the effects return signal is in parallel
with the signal through the amplifier). Use
the 4 front panel push buttons for assigning
either of the 2 Effects Loops to Channel 1,
Channel 2 or both.
N.B. Switching the effects loop IN (in Serial
mode) when there are no effects connected
will MUTE the amplifier as there will be no
signal returned to either Effects Return
socket.
EFFECTS LOOP (40 DSP & 60 DSP Combos,
60 DSP Head) - The Effects Loop on these
amplifiers is a Serial loop. This has two jack
sockets for Effects Send & Effects Return
signals; the Effects return socket also has an
12:16 pm
Page 10
Effects Return Level control associated with it
for adjusting the level of the returned signal.
SPEAKER EMULATED LINE OUTPUT (40
DSP & 60 DSP Combos, 60 DSP Head) - The
40 & 60 DSP combos and 60 DSP head have a
special Speaker Emulated Line Output jack
socket that can be used for direct recording
the guitar sound. This has a special
Equalisation circuit that Emulates the
characteristics of the loudspeaker/Output
stage combination.
SPEAKER OUTPUT SOCKETS & IMPEDANCE
SELECTOR (180 Head)
There are 3 speaker output sockets provided.
The one on the far right is fixed at 16 Ohms
should be used if you are driving just one 4 x
12 cabinet (16 Ohms). The other two sockets
are connected in parallel with the
IMPEDANCE SELECT switch controlling their
combined impedance. Follow the scheme
printed on the back panel (and reproduced
here) adjacent to these sockets for the
correct impedance to use for various speaker
combinations.
WARNING – Do not use open back cabinets
with this amplifier as the low-end power that
the amplifier produces will cause the cones
of the speakers to be damaged. Never run
the amplifier without a speaker connected as
this will damage the output transformer.
SPEAKER OUTPUT SOCKETS & IMPEDANCE
SELECTOR (40 DSP & 60 DSP Combos, 60
DSP Head) - There are 3 speaker output
sockets provided. The one on the far right is
fixed at 16 Ohms and should be used if you
are driving just one 4 x 12 cabinet (16 Ohms).
The other two sockets are connected in
parallel with the IMPEDANCE SELECT switch
controlling their combined impedance.
Rear Panel Facilities
INTERNAL SPEAKER 8 OHMS - This is the
socket for connection to the internal 8 Ohm
speaker. The impedance select switch should
be set to 8 Ohms for use with the internal
speaker only (as indicated by the graphics).
EXTERNAL SPEAKER 8 OHMS - This is an
external speaker socket for connecting to an
8 Ohms speaker such as a 2 x 12 cabinet
(normally 8 Ohms). This socket is in parallel
with the internal speaker socket, so if an
external 8 Ohms speaker is used with the
internal speaker still connected then the
impedance select switch will need to be set
to 4 Ohms (as indicated by the graphics).
WARNING - Never run the amplifier without a
speaker connected as this will damage the
output transformer.