1010music Toolbox Podręcznik użytkownika - Strona 9

Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Sprzęt nagrywający 1010music Toolbox. 1010music Toolbox 16 stron.
Również dla 1010music Toolbox: Skrócona instrukcja obsługi (2 strony)

Drukuj stronę

1010music Toolbox Podręcznik użytkownika

Toolbox has four gate sequencers that generate a sequence of gate signals to Gate Outputs 1 through 4. Each

Gate Sequencer on the touchscreen maps to one Gate Output jack. You configure the steps in the sequence by

using the control knobs and touch screen to control which steps in the sequence are ON or OFF.

To edit a Gate Sequence:

Press the HOME button if needed to return the Main Screen.

Touch one of the Gate Sequencers in column 2 to display the Gate Sequencer

screen. The gate sequencer grid displays a series of boxes that control whether the

gate signal is on (light blue) or off (gray) at each step in the sequence. The sequence

starts with step 1 in the lower left corner and scrolls right then up. During playback, a

white outline will move through the sequence of boxes to show the current playback

position.

Touch a box in the sequence grid to change its state.

Press the INFO button to toggle the display between the Gate Sequencer screen

and the Gate Parameters screen for this gate sequencer.

Use the Control Knobs to adjust the values of the following parameters:

Parameter

Description

Step Len

Controls the length of time the sequence

will spend on each step, in terms of

fractions of a bar.

Quant Size

Defines precisely when to restart the

sequence when using the internal clock.

When the sequence ends, toolbox will

wait until the start of the next Quant Size

interval to restart the sequence.

Step Count

The number of steps in the sequence. The

number of boxes on the screen will

remain the same, but if a value lower than

32 is selected, the sequencer will only

move through the number of steps

selected.

Clk Source

This parameter allows you to use an

alternative input as the clock signal. By

default, the toolbox internal clock (INT)

will be used.

Note:

If a value of a Gate Sequencer parameter is changed during playback of the sequence, the change

•

will take effect at the start of the next loop through the sequence.

Use the Note Sequencer

Toolbox's four Note Sequencers are piano roll style sequencers that generate both CV and MIDI outputs. The CV

output is in the form of a pair of gate and pitch signals for each Note Sequencer. The CV Output is monophonic and

will play back the most recently entered note for each step in the sequence. The CV gate signals for each Note

Sequencer are output through Gate Outputs 5 – 8, labeled Note Sequencer Gate Outputs in Figure 1: Front

Panel Overview. The CV Pitch signals are output through CV Outputs 1 - 4, labeled Note Sequencer Pitch

Outputs in Figure 1: Front Panel Overview. The CV signals on Gate Outputs 5 – 8 will output +5V for an ON

signal and 0V for an OFF signal. The pitch signals on CV Outputs 1 - 4 output 1 volt per octave and support a

range of 0 to 5 volts. Middle C is at 2 volts.

11/23/17 10:32 AM

Range of Values

1/64, 1/32T, 1/32, 1/16T,

1/16, 1/8T, 1/8, 1/4T, ¼,

1/2T, ½, 1 bar, 2 bars, 4

bars, 8 bars

(T= Triplet)

1/64, 1/32T, 1/32, 1/16T,

1/16, 1/8T, 1/8, 1/4T, ¼,

1/2T, ½, 1 bar, 2 bars

(T= Triplet)

1 through 32

INT, EXT1, EXT2, EXT3,

GATE1, GATE2, GATE3,

GATE4

Digital Heart – Analog Soul

Toolbox User Manual

Figure 8: Ga te

Sequencer Sc reen

Figure 9: Ga te

Sequencer P a ra meters

Screen

P. 9