Ashly PE-2400 Instrukcja obsługi - Strona 10

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Sprzęt komputerowy Ashly PE-2400. Ashly PE-2400 13 stron. Pe series high performance professional power amplifiers
Również dla Ashly PE-2400: Uwagi techniczne i specyfikacje (2 strony), Instrukcja instalacji i obsługi (2 strony), Arkusz specyfikacji (2 strony), Instrukcja obsługi (13 strony)

Drukuj stronę

Page - 10

Important Safety

Instructions – 2

Introduction - 3

The PE Series - 4

Power Output

Physical Description - 5

Stereo Mode, both channels driven

8 ohms, 20 Hz - 20 kHz, 1% THD

Installation – 6

4 ohms, 20 Hz - 20 kHz, 1% THD

Operation – 8

Bridged Mono Mode

Troubleshooting - 9

8 ohms, 20 Hz - 20 kHz, 1% THD

Parallel Mono Mode

Spec Table - 10

2 ohms, 20 Hz - 20 kHz, 1% THD

Measurements - 11

Signal to Noise (20 Hz-20 kHz,

unweighted):

Dimensions - 12

Voltage Gain:

Warranty - 13

Output Circuitry:

Power Requirements (1/8 Power

Pink Noise @ 4 Ohm):

All Models

Distortion (SMPTE, typical) - 8 ohm

load, 10 dB below rated power

Distortion (THD+N, typical) - 8 ohm

load, 10 dB below rated power, 20

Hz - 10 kHz

Frequency Response

Damping Factor - 8 ohm load, < 1

kHz

Input Impedance

Maximum Input Level:

Input Clipping

Cooling

Control Network:

Front Panel Indicators

Attenuators:

Input Connectors, each channel

Output connectors, each channel

Amplifier Protection

Load Protection

Power Cable Connector

Dimensions

Weight

PE-800

200 W

400 W

800 W

>98 dB

Bipolar, Class AB Bipolar, Class AB Bipolar, Class H Bipolar, Class H Bipolar, Class H Bipolar, Class H

420W

inrush current limitation, temperature monitoring heat-sinks, output DC protection, power transistor

15A Edison

22 lbs. (9.98kg)

Latency

A/D, D/A Converters:

DSP

Digital Input Type

Signal Flow Architecture

Available Processing Blocks

Equalization

Signal Delay

Compressor/Limiter, Gate, Meter

Signal Generator

Level Control

All Specifications Subject to Change or Improvement Without Notice.

Operator Manual – PE Series Amplifiers

PE-1200

PE-1800

300 W

500 W

600 W

900 W

1,200 W

1,800 W

1,300 W

1,800 W

>105 dB

>108 dB

640W

611W

temperature dependent speed-controlled axial fan

onboard, compatible with standard 100 MB Ethernet hardware

Per channel: Clip, -6 dB, -12 dB, -18 dB, Temp, Output current.

Overall: power, standby, protect, bridged mono, parallel mono, communications

Per channel: front panel, software, offset and remote

XLR female/TRS, Euroblock, XLR male (looping)

Speakon, screw terminals (Model 800 and 1200 only)

SOA protection, output over-current protection, mains fuses protection

20Amp

19"W x 3.5"H x 15.5"D (483mmW x 88.9mmH x 394mmD)

23 lbs. (10.43kg)

Optional Protea

/DSP Input Card

Analog - 1.512 ms at 48KHz sampling.

Digital - 0.784 ms at 96KHz sampling.

24-bit

32-bit, floating-point

AES3, 16-24 bit, 44.1 to 96 kHz.

"Click and hot plug" flexible architecture, non-compiling

Parametric, Notch, Graphic, Shelving, HPF/LPF, All pass

Up to 967msec any input/output

HPF/LPF

Up to 8th order (48 dB/octave)

Pink noise, White Noise, Sine Wave

With or without VCA-type subgrouping

PE-2400

PE-3000

PE-3800

700 W

900 W

1,100 W

1,200 W

1,500 W

1,900 W

2,400 W

3,000 W

3,800 W

2,400 W

3,000 W

3,800 W

>110 dB

>111 dB

>112 dB

26 dB, 32 dB or 1.5 V sensitivity (selectable)

790W

1010W

1220W

20 Hz - 20 kHz, +/- 0.15 dB

20 kOhm, balanced

Adjustable clip limiter

30A Twistlock

24 lbs. (10.89kg)

<.01%

> 400

+21 dBu