Cypress Semiconductor CY7C1333H Arkusz specyfikacji - Strona 3

Przeglądaj online lub pobierz pdf Arkusz specyfikacji dla Sprzęt komputerowy Cypress Semiconductor CY7C1333H. Cypress Semiconductor CY7C1333H 13 stron. Cypress 2-mbit (64k x 32) flow-through sram with nobl architecture specification sheet

Drukuj stronę
Pin Definitions
(100-pin TQFP Package)
Name
I/O
A
, A
, A
Input-
0
1
Synchronous
Input-
BW
[A:D]
Synchronous
Input-
WE
Synchronous
Input-
ADV/LD
Synchronous
CLK
Input-Clock
Input-
CE
1
Synchronous
CE
Input-
2
Synchronous
Input-
CE
3
Synchronous
Input-
OE
Asynchronous
Input-
CEN
Synchronous
ZZ
Input-
Asynchronous
DQ
I/O-
s
Synchronous
Mode
Input
Strap Pin
V
Power Supply Power supply inputs to the core of the device.
DD
V
I/O Power
DDQ
Supply
V
Ground
SS
NC
–
Document #: 001-00209 Rev. **
PRELIMINARY
Address Inputs used to select one of the 64K address locations. Sampled at the rising edge
of the CLK. A
are fed to the two-bit burst counter.
[1:0]
Byte Write Inputs, active LOW. Qualified with WE to conduct Writes to the SRAM. Sampled on
the rising edge of CLK.
Write Enable Input, active LOW. Sampled on the rising edge of CLK if CEN is active LOW. This
signal must be asserted LOW to initiate a Write sequence.
Advance/Load Input. Used to advance the on-chip address counter or load a new address. When
HIGH (and CEN is asserted LOW) the internal burst counter is advanced. When LOW, a new
address can be loaded into the device for an access. After being deselected, ADV/LD should be
driven LOW in order to load a new address.
Clock Input. Used to capture all synchronous inputs to the device. CLK is qualified with CEN. CLK
is only recognized if CEN is active LOW.
Chip Enable 1 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with
CE
, and CE
to select/deselect the device.
2
3
Chip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction with
CE
and CE
to select/deselect the device.
1
3
Chip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with
CE
and CE
to select/deselect the device.
1
2
Output Enable, asynchronous input, active LOW. Combined with the synchronous logic block
inside the device to control the direction of the I/O pins. When LOW, the I/O pins are allowed to
behave as outputs. When deasserted HIGH, I/O pins are three-stated, and act as input data pins.
OE is masked during the data portion of a Write sequence, during the first clock when emerging
from a deselected state, when the device has been deselected.
Clock Enable Input, active LOW. When asserted LOW the Clock signal is recognized by the
SRAM. When deasserted HIGH the Clock signal is masked. Since deasserting CEN does not
deselect the device, CEN can be used to extend the previous cycle when required.
ZZ "Sleep" Input. This active HIGH input places the device in a non-time critical "sleep" condition
with data integrity preserved. During normal operation, this pin can be connected to V
floating.
Bidirectional Data I/O Lines. As inputs, they feed into an on-chip data register that is triggered
by the rising edge of CLK. As outputs, they deliver the data contained in the memory location
specified by address during the clock rise of the Read cycle. The direction of the pins is controlled
by OE and the internal control logic. When OE is asserted LOW, the pins can behave as outputs.
When HIGH, DQ
are placed in a three-state condition. The outputs are automatically three-stated
s
during the data portion of a Write sequence, during the first clock when emerging from a deselected
state, and when the device is deselected, regardless of the state of OE.
Mode Input. Selects the burst order of the device.
When tied to Gnd selects linear burst sequence. When tied to V
burst sequence.
Power supply for the I/O circuitry.
Ground for the device.
No Connects. Not Internally connected to the die.
4M, 9M,18M,36M, 72M, 144M, 256M, 576M and 1G are address expansion pins and are not
internally connected to the die.
Description
or left floating selects interleaved
DD
CY7C1333H
or left
SS
Page 3 of 12
[+] Feedback